软包锂电制造完整工艺流程.ppt

《软包锂电制造完整工艺流程.ppt》由会员分享，可在线阅读，更多相关《软包锂电制造完整工艺流程.ppt（77页珍藏版）》请在三一办公上搜索。

1、2023/10/30,1,软包锂电制造流程 一、各控制工序流程图,cw,2023/10/30,2,配料,烤箱,作用:除湿、除潮,2023/10/30,3,搅拌机,2023/10/30,4,高速搅拌机,2023/10/30,5,搅拌机,2023/10/30,6,1、浆料粘度,粘度计,2023/10/30,7,涂布,浆料过篩;作用:将杂质、大颗粒筛出,上面放120目塞网,2023/10/30,8,涂布机,2023/10/30,9,作用:放铜箔、铝箔及单面极片,2023/10/30,10,半自动上料机,2023/10/30,11,2023/10/30,12,刀槽,2023/10/30,13,涂布刀,

2、千分表(作用:极片厚度参考数据),作用:料槽,高度需保持不变;,2023/10/30,14,2023/10/30,15,2023/10/30,16,纠偏器,作用:控制收卷整齐度,2023/10/30,17,自动上料缸,作用:保持液面高度稳定;浆料保持搅拌状态;,2023/10/30,18,段切机,分切机,极片段切,段切机,2023/10/30,19,2023/10/30,20,极片烘烤,烤箱,2023/10/30,21,辊压,辊压机,2023/10/30,22,冲切,2023/10/30,23,2023/10/30,24,极片分档,2023/10/30,25,电子称,档次栏,2023/10/3

3、0,26,极耳断切机,2023/10/30,27,2023/10/30,28,隔膜分切机,2023/10/30,29,隔膜断切机,隔膜除静电机,2023/10/30,30,叠片,2023/10/30,31,叠片夹具,2023/10/30,32,正负极点焊(超声波金属焊接机),2023/10/30,33,正极点焊,负极点焊,2023/10/30,34,2023/10/30,35,2023/10/30,36,2023/10/30,37,极耳修剪,2023/10/30,38,2023/10/30,39,预封,2023/10/30,40,包装,包装机,2023/10/30,41,热封模具,2023/1

4、0/30,42,自动胶纸切割机,2023/10/30,43,检测内阻,2023/10/30,44,2023/10/30,45,极片平压机,2023/10/30,46,卷绕,隔膜架,放极片盒,卷针,2023/10/30,47,电芯平压机,2023/10/30,48,极耳冲切机,2023/10/30,49,冲压成形,成形机,2023/10/30,50,2023/10/30,51,切料处,2023/10/30,52,成形机,2023/10/30,53,切料处,2023/10/30,54,冲头,2023/10/30,55,送料处,2023/10/30,56,框式液压包装盒成形机,2023/10/30,

5、57,冷却箱,2023/10/30,58,成型模具,2023/10/30,59,裁纸刀,2023/10/30,60,2023/10/30,61,垫板台、模块、弹簧刀,2023/10/30,62,注液,电解液搅拌机,2023/10/30,63,2023/10/30,64,2023/10/30,65,2023/10/30,66,预充,检测设备,全程监视器,2023/10/30,67,自动抽气机,2023/10/30,68,抽气平压机,将电芯的气体抽出.,2023/10/30,69,热封机,2023/10/30,70,切边机,2023/10/30,71,烫边机,2023/10/30,72,折边机,2023/10/30,73,打码机,作用:对电芯标识以便追述.,2023/10/30,74,上夹板,作用:保护电芯外观及降低电芯厚度.,2023/10/30,75,化成,检测设备,全程监视器,2023/10/30,76,2023/10/30,77,THE END,