【BS标准word原稿】BS EN 103282005 钢铁：表面加热后常规淬硬深度的测定Iron and steel. Determination of the convention.doc

《【BS标准word原稿】BS EN 103282005 钢铁：表面加热后常规淬硬深度的测定Iron and steel. Determination of the convention.doc》由会员分享，可在线阅读，更多相关《【BS标准word原稿】BS EN 103282005 钢铁：表面加热后常规淬硬深度的测定Iron and steel. Determination of the convention.doc（15页珍藏版）》请在三一办公上搜索。

1、豆丁网：Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:40:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSIBRITISH STANDARD BS EN10328:2005Iron and steel Determination of the conventional depth of hardening after surface heatingThe European Standard EN 10328:2005 has the status of aBritish Standa

2、rdICS 77.040.10 BS EN 10328:2005National forewordThis British Standard is the official English language version ofEN 10328:2005. It supersedes BS 6481:1984 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/72, Methods of physical and metallographic t

3、esting, which has the responsibility to:aid enquirers to understand the text;present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed;monitor related international and European developments and promul

4、gate them in the UK.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled

5、 “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or ofBritish Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with

6、a British Standard does not of itself confer immunity from legal obligations.Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:40:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSIThis British Standard was published under the authority of the Standards Policy and Strategy Committee on21 February

7、2005 BSI 21 February 2005ISBN 0 580 45510 6Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amd. No.Date

8、CommentsAmendments issued since publicationEUROPEAN STANDARD NORME EUROPENNEEUROPISCHE NORMEN 10328February 2005ICS 77.040.10English versionIron and steel - Determination of the conventional depth of hardening after surface heatingProduits sidrurgiques - Dtermination de la profondeur conventionnelle

9、 de trempe aprs chauffage superficielEisen und Stahl - Bestimmung der Einhrtungstiefe nach dem RandschichthrtenThis European Standard was approved by CEN on 3 January 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Europea

10、n Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, Fr

11、ench, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Repu

12、blic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T EUR O P EN DE NO

13、R M A L I S A TI ON EUR O P I S C H ES KOM I TEE F R NOR M UNG Management Centre: rue de Stassart, 36 B-1050 BrusselsLicensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:40:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 2005 CENAll rights of exploitation in any form and by any means reserved wor

14、ldwide for CEN national Members.Ref. No. EN 10328:2005: EEN 10328:2005 (E)Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:40:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSIContentsPage1Scope . 42Normative references . 43Terms and definitions . 44Conventions . 45Limits of the method. 56Test m

15、ethod. 57Test report . 65Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:40:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSIForewordThis document (EN 10328:2005) has been prepared by Technical Committee ECISS/TC 2 “Steel Physico- chemical and non-destructive testing”, the secretariat of which

16、 is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2005, and conflicting national standards shall be withdrawn at the latest by August 2005.This document supersedes EURONORM

17、116:1972.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, L

18、atvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:40:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI1ScopeThis document defines the test method for the

19、determination of the conventional depth of hardening after surface heating.2Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the reference

20、d document (including any amendments) applies.EN ISO 6507-1, Metallic materials - Vickers hardness test - Part 1: Test method. (ISO 6507-1:1997)3Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1hardness limithardness (expressed in HV and measured a

21、ccording to EN ISO 6507-1) defined compared to minimal hardness on the surface of the piece in question by the ratio :hardness limits = 0,80 X minimal surface hardness.3.2effective depth of hardness after surface heatingdistance between the surface of the piece to be tested and the point in the laye

22、r where the Vickers hardness is equal to the hardness limit, when measured under a strength of 9,807 N4Conventions4.1Expression of the effective depth of hardness after surface heatingThis parameter is designated by the symbol D.S.Its determination is expressed in millimetres, in the zone designated

23、 in the plan, on a piece, which may or may not have been rectified depending on the specification.4.2Special casesAll other values of hardness limit should be specially agreed. It should then be indicated by the symbol D.S.By agreement between the parties, loads differing from the test strength (9,8

24、07 N) may be used, these loads being within the range 4,903 and 49,03 N.Similarly, the use of the Rockwell method should be the subject of a prior agreement between the parties, which should also define the value of the hardness limit.Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:40:30 G

25、MT+00:00 2006, Uncontrolled Copy, (c) BSI5Limits of the methodThe test is carried out only on:a)layers hardened by quenching, the thickness of which is greater than 0,3 mm;b)pieces which, in the condition in question, have at the distance 3 x DS from the surface, a hardness less than : HV = a hardne

26、ss lower than the hardness limit 100.In the cases where these conditions are not satisfactory, the depth of hardening after surface heating, shall be defined by special agreement (see 4.2).6Test method6.1GeneralThe measuring is carried out, unless otherwise agreed, on a cross section of the piece in

27、 the hardened condition. The method of determining the effective depth of hardening after surface heating under test strength 9,807 N (see3.1) is the only one applicable in the case of litigation.6.2Principles of determinationThe depth of hardening is determined from the profile of hardness from a c

28、ross section normal to the surface. It is calculated graphically on a curve representing the variations of this hardness as a function of the distance from the surface of the piece.6.3Carrying out the determination6.3.1Preparation of the surface examinedThe section to be determined shall be polished

29、 so as to permit the correct determination of the dimensions of the hardness impressions. All necessary precautions shall be taken to avoid rounding the edges of this section adjacent to the surface and over heating the piece.6.3.2Determination of the hardnessThe hardness impressions are placed alon

30、g one or more lines normal to the surface and within a band width (w)1,5 mm wide (see Figure 1).The distance between the surface and successive impressions increases in 0,1 mm steps, the first point near the surface being 0,15 mm from the surface. In the case of very deep surface hardness, the dista

31、nces between the impressions can be greater, but the distance between the impressions (S) shall remain 0,1 mm in the immediate vicinity of the zone presumed to exhibit the maximum hardness. The distances between the surface and the impressions (d1, d2, d3) are determined from the centre of the latte

32、r: the absolute error should then not be greater than 25 m.These determinations are carried out on the surface in question in one or more specified regions by agreement between the parties and indicated on the drawing. For each region, the variation in hardness results should be plotted on a curve t

33、hat represents them as a function of the distance to the surface.6.4Result of the determinationThe curve or curves plotted make it possible to determine for each band of the surface in question, the distance to the surface from the point where the hardness is equal to the hardness limit, this distan

34、ce representing the effective depth of hardening after surface heating.Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:40:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI7Test reportThe test report should indicate: test piece description and its heat treatment ; area of the piece where the te

35、sts are carried out ; curves of the zones in question ; depth of hardness after surface heating ; parameters which have influenced the results.Key1Distance2HVFigure 1 Position of the hardness impressionsblankLicensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:40:30 GMT+00:00 2006, Uncontrolled

36、 Copy, (c) BSILicensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:40:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSIBS EN10328:2005BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparingBritish Standards. It presents th

37、e UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users ofBritish Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improv

38、e the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.Tel: +44 (0)20 8996 9000. Fa

39、x: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Te

40、l: +44 (0)20 8996 9001.Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are alsoavailable from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless o

41、therwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products

42、 and services. Contact the Information Centre.Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration.Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.Email: membershipbsi-.Information regarding onl