【BS英国标准】BS EN 11941999 Timber structures. Glued laminated timber. Strength classes and deter.doc

《【BS英国标准】BS EN 11941999 Timber structures. Glued laminated timber. Strength classes and deter.doc》由会员分享，可在线阅读，更多相关《【BS英国标准】BS EN 11941999 Timber structures. Glued laminated timber. Strength classes and deter.doc（11页珍藏版）》请在三一办公上搜索。

1、BRITISH STANDARDTimber structures Glued laminated timber Strength classes and determination of characteristic valuesThe European Standard EN 1194:1999 has the status of aBritish StandardICS 79.060.99; 91.080.20| BS EN1194:1999|Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 11:37:24 GMT+00:00

2、 2006, Uncontrolled Copy, (c) BSI|NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 1194:1999National forewordThis British Standard is the English language version of EN 1194:1999.The UK participation in its preparation was entrusted by Technical CommitteeB/525, Building an

3、d civil engineering structures, to Subcommittee B/525/5, Structural use of timber, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; mo

4、nitor related international and European developments and promulgate them in the UK.A list of organizations represented on this subcommittee can be obtained on request to its secretary.Additional informationIt should be noted that design stresses in the form of characteristic values(as described in

5、this standard) are suitable for use in designs carried out toENV 1995-1-1, but are not appropriate for use in permissible stress designs carried out to BS 5268-2.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in

6、the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using theFind facility of the BSI Standards Electronic Catalogue.A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are respon

7、sible for their correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 7 and a back cover.The BSI copyright notice displayed in this d

8、ocument indicates when the document was last issued.Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 11:37:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSIAmd. No.DateCommentsThis British Standard, having been prepared under the direction of the Sector Committee for Building and CivilEngineering,

9、 was published under the authority of the Standards Committee and comes into effect on 15 September 1999BSI 09-1999ISBN 0 580 30762 XAmendments issued since publicationEUROPEAN STANDARDEN 1194NORME EUROPE ENNEEUROPA ISCHE NORMApril 1999ICS 79.060.99; 91.080.20English versionTimber structures Glued l

10、aminated timber Strength classes and determination of characteristic valuesStructure en bois Bois lamelle -colle Classes de re sistance et de termination des valeurscaracte ristiquesHolzbauwerke Brettschichtholz Festigkeitsklassen und Bestimmung charakteristischer WerteLicensed Copy: sheffieldun she

11、ffieldun, na, Thu Oct 26 11:37:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSIThis European Standard was approved by CEN on 1 June1998.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national sta

12、ndard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other l

13、anguage made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece

14、, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.CENEuropean Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r NormungCentral Secretariat: rue de Stassart 36, B-1050 Brussels1999 CEN All right

15、s of exploitation in any form and by any means reserved worldwide for CEN nationalMembers.Ref. No. EN 1194:1999 EPage 7EN 1194:1999Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 11:37:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSIForewordThis European Standard has been prepared by Technical C

16、ommittee CEN/TC 124, Timber structures, the Secretariat of which is held by DS.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 1999, and conflicting national standards shall be withdrawn a

17、t the latest by October 1999.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembo

18、urg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.This standard is one of a series of standards for building materials. It was prepared by a working group under the joint convenorship of Association Franaise de Normalisation (AFNOR) and British Standards Instituti

19、on (BSI).This standard includes a normative annex on calculation of characteristic properties and a normative annex on examples of combinations of laminations and marking of glued laminated timber.BSI 09-1999Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 11:37:24 GMT+00:00 2006, Uncontrolled

20、 Copy, (c) BSIIntroductionA strength class system enables combinations of grade and species to be classified together with a common set of strength properties. Such a system simplifies the process of marketing glued laminated timber by reducing the number of options at the specification/supply inter

21、face.1 ScopeThis standard specifies a system of strength classes for horizontally laminated structural glued laminatedtimber with four or more laminations. A number of strength classes are defined and characteristic strength and stiffness properties and densities are given. This standard is currentl

22、y limited to softwood glued laminated timber.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated re

23、ferences, subsequent amendments to or revisions of any of these publications apply to this European Standard onlywhen incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.EN 338, Structural timber Strength classes. EN 384, Stru

24、ctural timber Determination of characteristic values of mechanical properties and density.EN 385: 1995, Finger jointed structural timber Performance requirements and minimum production requirements.EN 386, Glued laminated timber Performance requirements and minimum production requirements.EN 408, Ti

25、mber structures Structural timber and glued laminated timber Determination of some physical and mechanical properties.EN 1193, Timber structures Structural and glued laminated timber Determination of shear strength and mechanical properties perpendicular to the grain. ENV 1995-1-1, Eurocode 5 Design

26、 of timber structures Part 1-1: General rules and rules forbuildings.3 DefinitionsFor the purposes of this standard, the following definitions apply.3.1glued laminated timberstructural member formed by bonding together timber laminations with the grain running essentially parallel3.2characteristic v

27、aluesrefer to ENV 1995-1-13.3homogeneous glued laminated timberglued laminated timber with a cross-section where all laminations are of the same grade (strength class) and species (or species combinations)3.4combined glued laminated timberglued laminated timber with a cross-section comprising inner

28、and outer laminations of different grades(strength classes) and species (or species combinations)3.5horizontally laminated glued laminated timber see horizontal glulam defined in EN 386. For elements stressed in bending, the load is applied perpendicularto the wide faces of the laminations3.6 thickn

29、esslesser dimension perpendicular to the longitudinal axis3.7 widthgreater dimension perpendicular to the longitudinal axis3.8 depthdimension perpendicular to the longitudinal axis of a beam, in the plane of the bending forces4 SymbolsMain symbols:E0 modulus of elasticity parallel to the grain, in n

30、ewtons per square millimetre;f strength, in newtons per square millimetre;h depth of a bending specimen or width of a tension specimen, in millimetres;k factor;llength, in millimetres;rdensity, in kilograms per cubic metre; Subscripts:c compression;gproperties of glued laminated timber;jproperties o

31、f laminate end joints;k characteristic;lproperties of laminations;m bending; mean mean value; size size factor;t tension;vshear;0parallel to grain;90perpendicular to grain;055-percentile.5 Strength classes5.1 Table 1 and Table 2 give the characteristic strength, stiffness and density properties for

32、four standard strength classes.NOTE 1 The compression strength perpendicular to grain corresponds to the test method given in EN 1193. These values are approximately half of those used in some timber design codes for the strength verification of supports.NOTE 2 The shear strength values are derived

33、from actual values used in existing timber design codes.5.2 The values of bending strength are related to elements with a depth h of 600 mm. The values of tension strength parallel to grain are related to elements with a width h of 600 mm.6 Compliance6.1 GeneralGlued laminated members may be assumed

34、 to comply with the requirements for a strength class provided they meet the requirements of either 6.2 or 6.3.6.2 Compliance based on testsA glued laminated member can be assigned to one of the strength classes given in Tables 1 and 2 if its characteristic properties, derived from tests in accordan

35、ce with EN 408 and EN 1193, are not less than the values given in those tables.NOTE The basic required properties are the bending strength and the bending modulus of elasticity. The other properties necessary for design purposes can be taken directly from Tables 1 and 2.Licensed Copy: sheffieldun sh

36、effieldun, na, Thu Oct 26 11:37:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSITable 1 Characteristic strength and stiffness properties in N/mm2 and densities in kg/m3(for homogeneous glulam)Glulam strength classGL 24hGL 28hGL 32hGL 36hBending strength fm,g,k24283236Tension strength ft,0,g,kft,90,g,k1

37、6,50,419,50,4522,50,5260,6Compression strengthfc,0,g,kfc,90,g,k242,726,53,0293,3313,6Shear strength fv,g,k2,73,23,84,3Modulus of elasticity E0,g,meanE0,g,05E90,g,mean11 6009 40039012 60010 20042013 70011 10046014 70011 900490Shear modulus Gg,mean720780850910Density rg,k380410430450Table 2 Characteri

38、stic strength and stiffness properties in N/mm2 and densities in kg/m3(for combined glulam)Glulam strength classGL 24cGL 28cGL 32cGL 36cBending strength fm,g,k24283236Tension strength ft,0,g,kft,90,g,k140,3516,50,419,50,4522,50,5Compression strength fc,0,g,kfc,90,g,k212,4242,726,53,0293,3Shear stren

39、gth fv,k,g2,22,73,23,8Modulus of elasticity E0,g,meanE0,g,05E90,g,mean11 6009 40032012 60010 20039013 70011 10042014 70011 900460Shear modulus Gg,mean590720780850Density rg,k350380410430It is assumed that bending specimens have a depth h of 600 mm or more and a thickness b of 150 mm or more. It is a

40、ssumed that tension specimens have a width h of 600 mm or more and a thickness bof 150 mm or more. If the cross-section dimensions are lower than these reference values, the test results shall be multiplied by:6.3.2 The laminate end joints of all laminations shall meet at least one of the following

41、requirements a and b.Requirement a:ft,j,k $ 5+ ft,0,l,kwhereksize =b1500,05h6000,1ft,j,k is the characteristic tension strength of thelaminate end joints in full width determinedin accordance with EN 408 but with a knot-Test specimens shall have at least one laminate endjoint in the laminations in w

42、hich the tension stress is maximum.6.3 Compliance based on calculations6.3.1 The laminations shall have the necessary mechanical properties (derived in accordance withft,0,l,kfree specimen with a free length of 200 mm, in newtons per square millimetre; andis the characteristic tension strength of th

43、e laminations, as defined in 6.3.1, in newtons per square millimetre.EN 384 and EN 408) to produce mechanical properties of glued laminated timber equal to or greater than the values given in Tables 1 and 2.Formulae for calculating the mechanical properties of glued laminated timber from the laminat

44、ion properties are given in annex A. They shall be used to establish the mechanical properties for glulam strength classes of Tables 1 and 2, and may also be used to calculate the mechanical properties of glued laminated timber not corresponding to these strength classes.The basic requirements for the laminations w