【BS英国标准word原稿】BS EN 1248211998 Aluminium and aluminium alloys. Reroll stock for general app.doc

《【BS英国标准word原稿】BS EN 1248211998 Aluminium and aluminium alloys. Reroll stock for general app.doc》由会员分享，可在线阅读，更多相关《【BS英国标准word原稿】BS EN 1248211998 Aluminium and aluminium alloys. Reroll stock for general app.doc（13页珍藏版）》请在三一办公上搜索。

1、 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模糊、乱码等情况，请大家通过论坛消息与我联系。BRITISH STANDARDAluminium and aluminium alloys Reroll stock for general applications Part 1: Specifications for hot rolled reroll stockThe European Standard EN 12482-1:1998 has the status of aBritish StandardICS 77.150.10| BS EN12482-1:1998|Licens

2、ed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSI|NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 12482-1:1998National forewordThis British Standard is the English language version of EN 12482-1:1998.The UK participation

3、in its preparation was entrusted by Technical Committee NFE/35, Light metals and their alloys, to Subcommittee NFE/35/5, Wrought aluminium and aluminium alloys, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enqu

4、iries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK.A list of organizations represented on this subcommittee can be obtained on request to its secretary.Cross-referencesThe Bri

5、tish Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using theFind facility of the BSI Standards Electronic Catalogue.A British Sta

6、ndard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, a

7、n inside front cover, the EN title page, pages 2 to 5 and a back cover.Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSIAmd. No.DateText affectedThis British Standard, having been prepared under the direction of the EngineeringSector Committee

8、, was published under the authority of the Standards Committee and comes into effect on 15 December 1998BSI 1998ISBN 0 580 30338 1Amendments issued since publicationEUROPEAN STANDARDEN 12482-1NORME EUROPE ENNEEUROPA ISCHE NORMJuly 1998ICS 77.150.10Descriptors: aluminium, aluminium alloys, hot rolled

9、 products, reroll stock, definitions, specifications, delivery, orders, sales documents, dimensions, dimensional tolerances, tests, acceptance testing, marking, packingEnglish versionAluminium and aluminium alloys Reroll stock for general applications Part 1: Specifications for hot rolled reroll sto

10、ckAluminium et alliages daluminium Ebauches de relaminage pour applications ge ne rales Partie 1: Spe cifications pour e bauches obtenues parlaminage a chaudAluminium und Aluminiumlegierungen Vorwalzband fu r allgemeine Anwendungen Teil 1: Spezifikationen fu r warmgewalztes VorwalzbandLicensed Copy:

11、 sheffieldun sheffieldun, na, Sat Oct 28 08:51:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSIThis European Standard was approved by CEN on 1 July 1998.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status

12、of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A versi

13、on in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France

14、, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.CENEuropean Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r NormungCentral Secretariat: rue de Stassart 36, B-1050 Brussels1

15、998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nationalMembers.Ref. No. EN 12482-1:1998 EPage 5EN 12482-1:1998BSI 1998ForewordThis European Standard has been prepared byTechnical Committee CEN/TC 132, Aluminium andContentsPageLicensed Copy: sheffieldun she

16、ffieldun, na, Sat Oct 28 08:51:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSIaluminium alloys, the Secretariat of which is held byAFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1999,

17、 and conflicting national standards shall be withdrawn at the latest by January 1999.This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s).According to the CEN/C

18、ENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,

19、Switzerland and the United Kingdom.This standard is part of a series of two standards. The other standard deals with:EN 12482-2, Aluminium and aluminium alloys Reroll stock for general applications Part 2: Specifications for cold rolled reroll stock.Foreword 21Scope32Normative references33Definition

20、s34Technical conditions for inspection and delivery35Tolerances on dimensions46Inspection documents57Marking58Packing59Arbitration tests5Introduction 3Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSIIntroductionWhen hot or cold rolled strip i

21、n aluminium and aluminium alloy is to be rolled to thinner gauges in order to obtain cold rolled products such as sheets, strips, finstock and foil, this intermediate product is then called reroll stock.As the properties of the final products depend on the properties of the reroll stock and the furt

22、her process, it is therefore not practicable to specify in detailminimum requirements for all properties of reroll stock. This standard therefore gives only guidelines to the specifications which have to be established carefully between producer and purchaser prior to ordering.1 ScopeThis part of EN

23、 12482 specifies the particular requirements for wrought aluminium and aluminium alloys in the form of hot rolled strip. The thickness range covered is from 2,0 mm to 12 mm.It does not apply to hot rolled strip which is not rerolled, such as strip for general engineering or special applications.2 No

24、rmative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions o

25、f any of these publications apply to this European Standard onlywhen incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.EN 485-1, Aluminium and aluminium alloys Sheet, strip and plate Part 1: Technical conditions for inspecti

26、on and delivery.EN 515, Aluminium and aluminium alloys Wrought products Temper designations.EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition.EN 12258-1, Aluminium and aluminium alloys Terms and definitions Part 1: General terms.3

27、 DefinitionsFor the purposes of this European Standard, the definitions of aluminium and aluminium alloy according to EN 12258-1, the definitions of strip, hot rolled strip, sample, test piece and test according to EN 485-1, and the following apply.3.1reroll stockrolled strip destined to be rolled t

28、o thinner gauges in order to obtain cold rolled products such as sheets, strips, finstock and foil3.2hot rolled reroll stockreroll stock whose final thickness is obtained by hot rolling4 Technical conditions for inspection and delivery4.1 Orders or tendersThe order or tender shall define the product

29、 required and shall contain at least the following information:a) the form and type of product:1) the designation of the aluminium or aluminium alloy in accordance with EN 573-3;2) the application intended by the purchaser: the form, final thickness and temper to which the product is transformed at

30、the purchasers works; any indication on intended surface treatments;b) the temper of the product for delivery in accordance with EN 515;c) whether mechanical properties are to be specified;d) the number of this European Standard or a specification number, or, where none exists, the properties agreed

31、 between purchaser and producer; e) the dimensions and shape of the product: thickness; width; net mass of the coil; internal and external diameters of the coil;f) the quantity: number of coils; minimum and maximum mass of coils; tolerance on quantity if required;g) any requirements for inspection d

32、ocuments;h) any special requirements for packing: mass per coil; design of pallet;i) any special requirements agreed between producer and purchaser: marking of products; additional property requirements.4.2 Requirements4.2.1 Production and manufacturing processUnless otherwise stated in the order, t

33、he production and manufacturing processes shall be left to the discretion of the producer. Unless it is explicitly stated in the order no obligation shall be placed on the producer to use the same processes for subsequentand similar orders.4.2.2 Quality controlThe producer shall be responsible for t

34、he performance of all inspection and tests required by the relevant European Standard and/or the particular specification, prior to shipment of the product.If the purchaser wishes to inspect the product at the producers works, he shall notify the producer at the time of placing the order.4.2.3 Freed

35、om from defectsThe product shall be free from defects prejudicial to its suitable and proper use. It shall have a smooth and clean rolling surface.The surface condition shall be agreed between producer and purchaser.4.2.4 Chemical compositionThe chemical composition shall comply with the requirement

36、s as specified in EN 573-3.If the purchaser requires content limits for elements not specified in the above standard, these limits shall be stated on the order, after agreement between producer and purchaser.4.2.5 Mechanical propertiesIf mechanical properties are required, they shall be4.2.7 Other p

37、ropertiesAdditional property requirements, such as surface aspect, edge trimming, etc., shall be agreed between producer and purchaser and stated on the order.4.3 Test procedures4.3.1 Chemical compositionChemical composition shall be tested as specified inEN 485-1.4.3.2 Tensile testSelection and pre

38、paration of samples and test pieces shall be in conformity with EN 485-1.4.3.3 RetestsRetests shall be carried out in conformance withEN 485-1.5 Tolerances on dimensions5.1 ThicknessTolerances on thickness are specified in Table 1. Tolerances on thickness for nominal thickness between8 mm and 12 mm

39、shall be agreed between producerand purchaser.5.2 Width5.2.1 Strip without trimmed edgesTolerances on width for strip without trimmed edges shall be agreed between producer and purchaser and stated on the order.5.2.2 Strip with trimmed edgesFor specified width over 600 mm up to 2 500 mm, the+8agreed

40、 between producer and purchaser and stated on the order.4.2.6 Tolerances on dimensionsThe tolerances on dimensions shall be in conformity with those specified in clause 5 or agreed between producer and purchaser and stated on the order.tolerance on width is0 mm.Table 1 Tolerances on thicknessDimensi

41、ons in millimetresLicensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSISpecified thicknessTolerance on thickness for specified widthOverUp to and includingOver 1 250 up to and including 1 600Over 1 600 up to and including 2 000Over 2 000 up to and

42、 including 2 5002,01)40,300,350,40450,350,400,45560,400,450,50680,450,500,551) Including thickness of 2,0 mm.Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:34 GMT+00:00 2006, Uncontrolled Copy, (c) BSI6 Inspection documentsInspection documents shall be in conformity with those specifie

43、d in EN 485-1.7 MarkingUnless otherwise agreed at the time of ordering, the following marking requirements shall apply:a) name or mark of the producer; b) alloy and temper designation; c) order number;d) ordered dimensions;e) production batch number and mass.Each of these items shall be given on a l

44、abel, which is to be attached to every coil or pack.8 PackingThe packing requirements shall be agreed between producer and purchaser.9 Arbitration testsIn cases of dispute concerning conformity with the requirements of this European Standard or specification cited on the order, before rejecting the products, testing and examination shall be carried out by an a