BS英国标准BS EN 501313 Alarm systems — Intrusion and holdup systems — Part 3 Control and i.doc

《BS英国标准BS EN 501313 Alarm systems — Intrusion and holdup systems — Part 3 Control and i.doc》由会员分享，可在线阅读，更多相关《BS英国标准BS EN 501313 Alarm systems — Intrusion and holdup systems — Part 3 Control and i.doc（79页珍藏版）》请在三一办公上搜索。

1、BS EN 50131-3:2009BSI British StandardsAlarm systems Intrusion and hold-up systems Part 3: Control and indicating equipmentNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWraising standards worldwideBS EN 50131-3:2009BRITISH STANDARDNational forewordThis British Standard is the

2、UK implementation of EN 50131-3:2009. It supersedes DD CLC/TS 50131-3:2003 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee GW/1, Electronic security systems, to Subcommittee GW/1/1, Alarm components.A list of organizations represented on this committee

3、 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2009ISBN 978 0 580 61916 8ICS 13.310Compliance with a British Standard cannot confer immunity from legal obliga

4、tions.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 30 April 2009Amendments issued since publicationAmd. No. Date Text affectedBS EN 50131-3:2009EUROPEAN STANDARDEN 50131-3NORME EUROPENNEEUROPISCHE NORM March 2009 ICS 13.310Supersedes CLC/TS

5、 50131-3:2003English versionAlarm systems - Intrusion and hold-up systems -Part 3: Control and indicating equipmentSystmes dalarme -Systmes dalarme contre lintrusion et les hold-up -Partie 3: Equipement de contrle et de signalisationAlarmanlagen -Einbruch- und berfallmeldeanlagen - Teil 3: Melderzen

6、traleThis European Standard was approved by CENELEC on 2009-02-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographi

7、cal references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a C

8、ENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary

9、, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.CENELECEuropean Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Eu

10、ropisches Komitee fr Elektrotechnische NormungCentral Secretariat: avenue Marnix 17, B - 1000 Brussels 2009 CENELEC -All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.Ref. No. EN 50131-3:2009 EForewordThis European Standard was prepared by the Technical C

11、ommittee CENELEC TC 79, Alarm systems. The text of the draft was submitted to the Unique Acceptance Procedure and was approved byCENELEC as EN 50131-3 on 2009-02-01.This European Standard supersedes CLC/TS 50131-3:2003. The following dates were fixed: latest date by which the EN has to be implemente

12、d at national level by publication of an identicalnational standard or by endorsement(dop)2010-02-01 latest date by which the national standards conflictingwith the EN have to be withdrawn(dow)2012-02-01EN 50131 will consist of the following parts, under the general title “Alarm systems Intrusion an

13、d hold-up systems”:Part 1System requirementsPart 2-2Intrusion detectors - Passive infrared detectorsPart 2-3Requirements for microwave detectorsPart 2-4Requirements for combined passive infrared and microwave detectors Part 2-5Requirements for combined passive infrared and ultrasonic detectors Part

14、2-6Opening contacts (magnetic)Part 2-7-1Intrusion detectors Glass break detectors (acoustic) Part 2-7-2Intrusion detectors Glass break detectors (passive) Part 2-7-3Intrusion detectors Glass break detectors (active) Part 3Control and indicating equipmentPart 4Warning devicesPart 5-3Requirements for

15、interconnections equipment using radio frequency techniquesPart 6Power suppliesPart 7Application guidelinesPart 8Security fog device/systemsBS EN 50131-3:2009EN 50131-3:2009 19 IntroductionThis document is based on the revision of the Technical Specification originally edited by the CENELEC TC 79/WG

16、 3, then submitted to the formal vote and finally approved by CENELEC as CLC/TS 50131-3 on 2003-05-19.The work done by WG 3 is the result of the comments raised by the National Committees, members of CENELEC and of harmonisation with EN 50131-1:2006 + A1:2009 prepared by TC 79/WG 1; for this reason

17、the reader has to take into account EN 50131-1:2006 + A1:2009, which has to be considered as a “master” document for this EN 50131-3.Repetition of definitions and requirements contained in EN 50131-1 have been eliminated from this EN 50131-3, in order to minimise conflict in the event of changes to

18、EN 50131-1, except where repetition is deemed essential for the clarity of this document.Reference has been included to various implications arising from the detector standards. Full detail of the interconnection requirements could be the subject of a future standard.A number of requirements are con

19、tained in this standard for which a formal test procedure can only be written by defining (and hence restricting) the technology by which the requirement is achieved. Accordingly, it has been recognised that such functions can be tested only by agreement between manufacturer and test house, accordin

20、g to documented information relating to how the required functionality has been achieved.A table to cross reference EN 50131-1 requirements against this EN 50131-3 and tests has been included in Annex D.ContentsIntroduction.31Scope .62Normative references .73Definitions and abbreviations .73.1Defini

21、tions .73.2Abbreviations .104Equipment attributes .104.1General .104.2Functionality .115CIE construction .116Security grade .117Environmental performance .117.1Requirements.117.2Environmental and EMC tests .118Functional requirements .128.1Inputs .128.2Outputs.138.3Operation .138.4Processing .188.5I

22、ndication .198.6Notification outputs .208.7Tamper security (detection/protection) .218.8Interconnections.238.9Timing .248.10Event recording .248.11Power supply.259Product documentation .259.1Installation and maintenance .259.2Operating instructions .2610Marking and labelling .2611Tests.2611.1Test co

23、nditions .2711.2Test procedures .2811.3Reduced functional test .2811.4Functional tests .2911.5Access level .4011.6Authorization requirements .4111.7Operational tests .4611.8Tamper security tests.5611.9Substitution tests.5911.10Testing of I&HAS timing performance .5911.11Testing for interconnections

24、.6011.12Event log .6111.13Marking and documentation.6211.14Environmental and EMC tests .63Annex A (informative) Interconnection types .65Annex B (informative) Summary of timing requirements .67Annex C (normative) Use of non-I&HAS interface .68Annex D (informative) Summary of function cross reference

25、s.69FiguresFigure A.1 Specific wired interconnections .65Figure A.2 Non-specific wired interconnections .65Figure A.3 Wire-free interconnections .66TablesTable 1 Recognition of additional fault conditions .12Table 2 Recognition of biometric keys .15Table 3 Time intervals for methods of authorization

26、 used in combination .15Table 4 Detection of repeated invalid authorization attempts .16Table 5 Monitoring of processing .19Table 6 Indications supplementary to those of EN 50131-1 .20Table 7 Tamper protection .22Table 8 Tamper detection.22Table 9 Tool dimension for tamper detection .23Table 10 Removal from mounting .23Ta