高速公路边坡锚索施工首件方案.doc

《高速公路边坡锚索施工首件方案.doc》由会员分享，可在线阅读，更多相关《高速公路边坡锚索施工首件方案.doc（61页珍藏版）》请在三一办公上搜索。

1、石忠高速B14合同段石忠高速公路B14合同段(ZK63+002.217-ZK63+394.5左侧边坡加固工程)预应力锚索框架梁首件施工组织设计及施工方案路桥集团国际建设股份有限公司石忠高速公路B14合同段项目经理部二00七年八月十二日一、分 项 工 程 概 况我部计划对ZK63+002.217-ZK63+300左侧边坡加固工程锚索施工。为保证高速公路整个锚索项目的工程质量，本着“预防为主，先导试点”的原则，在锚索施工全面铺开之前，先做锚索首件工程。锚索首件工程选定为ZK63+220-ZK63+300段锚索工程，结构形式为预应力8束锚索框架梁，格子梁采用C25,垫,磴采用C30砼。桩号为ZK63

2、+220-ZK63+300，开工日期2007.9. 1，完工日期2007、10、26。二、人员配置现场负责人： 质检工程师： 试验工程师： 质 检 员： 工程技术员： 工程测量员： 安 全 员： 混 凝 土工： 10 人模 板 工： 8 人 钢 筋 工: 6 人普 工： 6 人三、机械设备的配置 1、 张拉千斤顶： 2套 2、弯曲机： 1套 3、断筋机： 1台 4、500型拌和机： 2台 5、插入式振动棒 2台、 6、空 压 机： 3台 7、自卸车1辆 8、风钻2台9、压浆机：1台 10、发电机1台 11：潜水泵： 1台 12：人力手推车： 5台 13、电焊机：2台 14、卷扬机：1台 四、施

3、工工艺1、锚孔测放边坡施工边挖边加固：即开挖一级，防护一级，不得一次开挖到底。根据各工点工程立面图，按设计要求，将锚孔位置准确测放在坡面上，孔位误差不得超过50mm。2、钻孔设备钻孔机具的选择：根据锚固地层的类别、锚孔孔径、锚孔深度、以及施工场地条件等来选择钻孔设备。岩层中采用钻孔直径130的潜孔冲击成孔；在岩层破碎易于塌缩孔和卡钻埋钻的地层中采用跟管钻进技术。3、钻机就位 锚孔钻进施工，搭设满足相应承载能力和稳固条件的脚手架，根据坡面测放孔位，准确安装固定钻机，并严格认真进行机位调整，确保锚孔开钻就位纵横误差不得超过50mm，高程误差不得超过100mm，钻孔倾角和方向符合设计要求，倾角允许误

4、差位1.0，方位允许误差2.0。4、钻进方式钻孔要求干钻，禁止采用水钻，以确保锚索施工不致于恶化边坡岩体的工程地质条件和保证孔壁的粘结性能。钻孔速度根据使用钻机性能和锚固地层严格控制，防止钻孔扭曲和变径，造成下锚困难或其它意外事故。5、钻进过程钻进过程中对每个孔的地层变化，钻进状态（钻压、钻速）、地下水及一些特殊情况作好现场施工记录。如遇塌孔缩孔等不良钻进现象时，须立即停钻，及时进行固壁灌浆处理（灌浆压力0.10.2MPa），待水泥砂浆初凝后，重新扫孔钻进。6、孔径孔深钻孔孔径、孔深要求不得小于设计值。为确保锚孔直径，要求实际使用钻头直径不得小于设计孔径。为确保锚孔深度，要求实际钻孔深度大于设

5、计深度0.2m以上。7、锚孔清理 钻进达到设计深度后，不能立即停钻，要求稳钻12分钟，防止孔底尖灭、达不到设计孔径。钻孔孔壁不得有沉碴及水体粘滞，必须清理干净，在钻孔完成后，使用高压空气（风压0.20.4MPa）将孔内岩粉及水体全部清除出孔外，以免降低水泥砂浆与孔壁岩土体的粘结强度。除相对坚硬完整之岩体锚固外，不得采用高压水冲洗。若遇锚孔中有承压水流出，待水压、水量变小后方可下安锚筋与注浆，必要时在周围适当部位设置排水孔处理。如果设计要求处理锚孔内部积聚水体，一般采用灌浆封堵二次钻进等方法处理。8、锚孔检验锚孔钻造结束后，须经现场监理检验合格后，方可进行下道工序。孔径、孔深检查一般采用设计孔径

6、、钻头和标准钻杆在现场监理旁站的条件下验孔，要求验孔过程中钻头平顺推进，不产生冲击或抖动，钻具验送长度满足设计锚孔深度，退钻要求顺畅，用高压风吹验不存明显飞溅尘碴及水体现象。同时要求复查锚孔孔位、倾角和方位，全部锚孔施工分项工作合格后，即可认为锚孔钻造检验合格。9、锚索体制作及安装预应力锚索体由锚梁头、自由段、锚固段三部分组成。采用压力分散型锚索，锚固段由三个单元锚索组成，每个单元锚索分别由两根无粘结钢绞线内锚于钢质承载体组成，钢绞线通过特制的挤压簧和挤压套对称地锚固于钢质承载体上，要求单根的连接强度大于200KN。钢质承载体要求采用45号钢材加工制作，其厚度不小于2cm。钢绞线采用j15.2

7、4mm高强度低松弛无粘结预应力钢绞线。每根钢绞线均采用环氧树脂涂膜层，22聚乙烯管和润滑脂保护层三层防腐型式，砼垫磴预留孔之间的锚索采用波纹管进行防护。安装前，要确保每根钢绞线顺直，不扭不叉，排列均匀，除锈、除油污，对有死弯、机械损伤及锈坑处剔出。钢绞线沿锚索体轴线方向每1.01.5m设置一架线环，保证锚索体保护层厚度不小于20mm。安装锚索体前再次认真核对锚孔编号，确认无误后再用高压风吹孔，人工缓缓将锚索体放入孔内，用钢尺量出孔外露出的钢绞线长度，计算孔内锚索长度（误差控制在50mm范围内），确保锚固长度。10、锚固注浆注浆采用孔底返浆法的一次灌浆方式，M35水泥砂浆，经试验比选后确定施工配

8、合比。实际注浆量一般要大于理论的注浆量，或以锚具排气孔不再排气且孔口浆液溢出浓浆作为注浆结束的标准。注浆结束后，将注浆管、注浆枪和注浆套管清洗干净，同时做好注浆记录。11、地梁制作地梁采用C25、磴采用C30混凝土整体浇注。基础先铺垫2cm砂浆调平层，再进行钢筋制作安装，钢筋接头需错开，同一截面钢筋接头数不得超过钢筋总根数的1/2，且有焊接接头的截面之间的距离不得小于1m。如锚索与竖梁箍筋相干扰，可局部调整箍筋的间距。砼浇注，尤其在锚孔周围，钢筋较密集，一定要仔细振捣，保证质量。钢筋制作检验项目检 查 项 目允许偏差（mm）1受力钢筋间距(mm)梁、板、拱肋102箍筋、横向水平钢筋、螺旋筋间距

9、（mm）103钢筋骨架尺寸长104宽、高或直径55保护层厚度（mm）柱、梁、拱肋5模板制作检验项目项 目允许偏差（mm）1模板内部尺寸5,02模板相邻两板表面高低差+2，-53模板表面平整24预埋件中心线位置35预留孔洞中心线位置106预留孔洞截面内部尺寸+10，0 地梁C25，垫磴C30混凝土配料分别采用以下参数进行配制：水泥采用石柱“方斗山”P.o32.5水泥。水泥用量采用375kg/m3，水灰比采用0.48，含砂率采用36%，并掺入NF-2型缓凝高效减水剂掺量0.9%,以改善混凝土的性能,塌落度90110mm，水泥用量采用417kg/m3，水灰比采用0.42，含砂率采用35%，并掺入NF

10、-2型缓凝高效减水剂掺量0.9%,以改善混凝土的性能,塌落度90110mm,已通过验证实验，混凝土强度能满足设计要求。混凝土每一台班用量不大，采用强制式拌和机拌和，利用两辆手推车水平运输至提升料斗，利用提长料斗垂直运输。这样能保证及时、不间断地进行混凝土的浇筑。 浇筑混凝土前，将模板内杂物和钢筋上的油污擦洗干净，并对模板进行加固，经监理工程师检查合格后，方可进行混凝土浇筑。 在混凝土浇筑过程中，首先派有经验的混凝土工负责，采用插入式振动棒，竖梁振动棒从预先留设的孔中放入振捣，横梁从上口放入振动棒，移动间距不超过其作用半径的1.5倍，与模板应保持510cm的间距。浇筑过程中一个工作台班制作试件三

11、组(不含监理抽检)12、锚索张拉及锁定、封锚通过现场张拉试验，确定张拉锁定工艺。锚索的张拉及锁定分级进行，严格按照操作规程执行。在设计张拉完成610d后再进行一次补偿张拉，然后加以锁定。补偿张拉后，从锚具量起，留出长510cm钢绞线，其余部分截去，须用机械切割，严禁电弧烧割。最后用水泥净浆注满锚垫板及锚头各部分空隙，然后对锚头采用不低于30MPa的混凝土进行封锚，防止锈蚀和兼顾美观。五、施工质量控制（1）、钢筋骨架质量控制a、钢筋进库后，验收出厂合格证和试验报告单，对原材及焊接接头取样复试，检验合格后方可使用。b、钢筋成品表面应洁净，使用前清除表面漆皮和锈迹。c、钢筋应平直，弯折成盘和局部弯曲

12、的钢筋应调直使用。d、严格控制焊接质量，骨架尺寸准确、安装准确，保护层厚度满足设计要求。(2)、模板质量控制a、模板具有足够的强度、刚度和稳定性，满足图纸设计要求。b、侧模板顶面平整光滑，安装前将模内杂物清理干净，并涂刷脱模剂，脱模剂禁止采用废机油。c、模板位置安装正确，严格控制好标高，拼缝严密，确保混凝土浇筑振捣过程中不变形、不漏浆。d、混凝土浇筑期间设专人对模板随时进行检查，发现有松动和变形及时调整。e、掌握拆模时间，侧模待混凝土强度达2.5Mpa时方可拆模。(3)、混凝土质量控制预先做好砂石材料的级配试验，验收水泥出厂合格证及质保书，并取样复试，测定水泥各项技术指标。测定砂石含水量，确定

13、合理的施工配合比，施工过程严格控制好配合比和坍落度，振捣密实，做到浇筑好的地梁表面平整、光洁，无蜂窝麻面或其他缺陷，并且按规范要求认真做好试压块，进行标准养护。(4)、质量控制：a、加强施工质量监督检查，内部实行班组自检、工区复检制度。 b、加强技术管理工作，实行设计技术交底、质量检测标准交底制度，认真落实岗位责任制。 c、加强中间检查，对施工方案、安全及技术措施、材料试验方法等进行认真的审核把关，并定期检查执行情况，做到以防为主，防检结合。 d、严格原材料品质检验制度，原材料成品、半成品必须经检验合格后方准使用。 e、支持和协助监理工程师的工作，尊重监理人员的意见和建议。 f、严格工程质检及

14、隐蔽工程交验制度，严格班组管理，实行安全、质量一票否决制，通过优良的工作质量确保优良的工序质量，从而确保优良的工程质量。j、加强砼养护工作，高温季节要及时喷淋水管向砼表面喷水养护。质量保证体系流程图锚索施工处理班组自检不合格测量保证 试验检测质量检测负责人： 负责人： 负责人： 项目部自检不合格合格分析原因提出处理措施测量保证 试验检测 质量检测负责人： 负责人： 负责人： 不合格合格 监理检验验收 六、施工工艺 锚索施工工艺流程图测量放洋钻孔砂浆拌和下锚砂浆试件制作灌浆钢筋制安砼试件制作模板制安砼拌和砼浇筑砼养护预应力张拉封锚七、安全保证措施1）、建立健全安全生产管理机构，成立以项目经理为组

15、长的安全生产领导小组，全面负责并领导本项目的安全生产工作。2）、本项目实行安全生产三级管理，即、一级管理由经理负责，二级管理由专职安全员负责，三级管理由领工员（或班组长）负责，各作业点设立安全监督岗。3）、按照我公司颁布的安全生产责任制的要求，落实各级管理人员和操作人员的安全生产责任制做到纵向到底，横向到边，各自作好本岗位的安全工作。4）、实行逐级安全技术交底制，由经理部组织有关人员对工程项目或专项进行书面详细安全技术交底，凡参加安全技术交底的人员要履行签字手续，并保存资料。八、文明施工措施施工中尽量大限度维护原来的地貌地形，保持原来的生态环境。认真作好施工场地规划和安排，根据场地实际情况合理

16、地进行布置，现场悬挂宣传标志，营造良好施工氛围。施工区内道路通畅、平坦、整洁，不乱堆乱放，无散落物；无散落的杂物及散物；场地排水成系统，达到畅通不堵。施工现场临时生活、生产区合理规划,布局合理有序生产、生活区分开搭设,拌和场地采用C15厚5cm砼硬化,料场采用空心砖砌筑隔离墙,以此防止材料混合堆放,并搭建水泥库,架空覆盖堆。在施工作业中，力争把本合同打造成一条优质原生态高速公路。九、环境保护措施为确保文明施工，促进施工顺利进行，我部将采取以下环境保护措施。1、全线划出标识明确、醒目的施工用地界线，禁止越界施工2、堆料场远离饮用水源地、水井、河、渠、池塘等地表水体。3、严格要求，规范操作。禁止超

17、规范砍伐施工界线外的植被。4、车辆行驶车道及范围作标识和划定，禁止车辆随意在桥上行驶。5、在工地及周边设立爱护野生动物和自然植被的宣传牌，施工工人进场后，立即进行生态保护教育，明确保护责任。6、严禁施工人员乱砍滥伐、偷伐盗猎、肆意捕食鱼类、鸟类及其它野生动物。7、对车辆驾驶员进行安全教育，最大程度减小施工燥声污染。 （英文版 ） Two regulations promulgated for implementation is in the party in power for a long time and the rule of law conditions, the implementa

18、tion of comprehensive strictly strategic plan, implementation in accordance with the rules and discipline to manage the party, strengthen inner-party supervision of major initiatives. The two regulations supporting each other, the adhere to a positive advocate, focusing on morality is of Party membe

19、rs and Party leading cadres can see, enough to get a high standard; around the party discipline, disciplinary ruler requirements, listed as negative list, focusing on vertical gauge, draw the party organizations and Party members do not touch the bottom line . Here, the main from four square face tw

20、o party rules of interpretation: the first part introduces two party Revised regulations the necessity and the revision process; the second part is the interpretation of the two fundamental principles of the revision of laws and regulations in the party; the third part introduces two party regulatio

21、ns modified the main changes and needs to grasp several key problems; the fourth part on how to grasp the implementation of the two regulations of the party. and revised the necessity and revised history of the CPC Central Committee the amendment to the Chinese Communist Party members and leading ca

22、dres honest politics several guidelines and column 1 by 2015 to strengthen party laws and regulations focus. Two party regulations revision work lasted a Years, pooling the wisdom of the whole party, ideological consensus, draw historical experience, respect for the wisdom of our predecessors, which

23、 reflects the unity of inheritance and innovation; follow the correct direction, grasp the limited goals, adhere to the partys leadership, to solve the masses of the people reflect a focus on the problem. The new revision of the and , reflects the partys 18 and the eighth session of the third, the s

24、pirit of the fourth plenary session, reflecting the experience of studying and implementing the General Secretary Xi Jinping series of important speech, reflects the partys eighteen years comprehensive strictly practice. (a) revised two regulations of the party need of in based on revised, the promu

25、lgation and implementation of January 2010, to strengthen the construction of the contingent of leading cadres play an important role. But with the party to manage the party strictly administering the deepening, has not been able to fully meet the actual needs. Content is too complicated, eight proh

26、ibition, 52 are not allowed to hard to remember, and also difficult to put into practice; the second is concisely positive advocated by the lack of prohibited provisions excessive, no autonomy requirements; the third is banned terms and discipline law, both with the party discipline, disciplinary re

27、gulations repeat and Criminal law and other laws and regulations repeat; the fourth is to clean the theme is not prominent, not for the existing problems, and is narrow, only needle of county-level leading cadres above. is in 1997 based on revision, in December 2003 the promulgation and implementati

28、on, to strengthen the construction of the party play very important role. Along with the development of the situation, which many provisions have been unable to fully meet the comprehensive strictly administering the practice needs. One is Ji law, more than half of the provisions and criminal law an

29、d other countries laws and regulations Repetition; two is the political discipline regulations is not prominent, not specific, for violation of the party constitution, damage the authority of Party Constitution of misconduct lack necessary and serious responsibility to pursue; third is the main disc

30、ipline for the leading cadres, does not cover all Party members. Based on the above situation, need to and the two is likely to be more relevant regulations first amendment. By revising, really put the authority of Party discipline, the seriousness in the party tree and call up the majority of Party

31、 members and cadres of the party constitution of party compasses party consciousness. (II) two party regulations revision process the Central Committee of the Communist Party of China attaches great importance to two regulations revision . Xi Jinping, general books recorded in the Fifth Plenary Sess

32、ion of the eighth session of the Central Commission for Discipline Inspection, on the revised regulations made clear instructions. According to the central deployment, the Central Commission for Discipline Inspection from 2014 under six months begin study two regulations revision. The Standing Commi

33、ttee of the Central Commission for Discipline Inspection 4 review revised. Comrade Wang Qishan 14 times held a special meeting to study two regulations revision, amendment clarifies the direction, major issues of principle, path and target, respectively held a forum will listen to part of the provin

34、ce (area) secretary of the Party committee, Secretary of the Discipline Inspection Commission, part of the central ministries and state organs Department The first party committee is mainly responsible for people, views of experts and scholars and grassroots party organizations and Party members. Ap

35、proved by the Central Committee of the Communist Party of China, on 7 September 2015, the general office of the Central Committee of the Party issued a notice to solicit the provinces (autonomous regions, municipalities) Party, the central ministries and commissions, state ministries and commissions

36、 of the Party (party), the General Political Department of the military, every 3 people organization of Party of two regulations revision opinion. Central Commission for Discipline Inspection of extensive solicitation of opinions, careful study, attracting, formed a revised sent reviewers. In Octobe

37、r 8 and October 12, Central Committee Political Bureau Standing Committee and the Political Bureau of the Central Committee After consideration of the two regulations revised draft. On October 18, the Central Committee of the Communist Party of China formally issued two regulations. Can say, two law

38、s amendment concentrated the wisdom of the whole party, embodies the party. Second, and revision of the basic principles of two party regulations revision work and implement the partys eighteen, ten eight plenary, the spirit of the Fourth Plenary Session of the Eleventh Central Committee and General

39、 Secretary Xi Jinping important instructions on the revised and , highlighting the ruling party characteristics, serious discipline, the discipline quite in front of the law, based on the current, a long-term, advance as a whole, with Bu Xiuding independent and . Main principle is: first, adhere to

40、the party constitution to follow. The constitution about discipline and self-discipline required specific, awaken the party constitution of party compasses party consciousness, maintaining the authority of the constitution. General Secretary Xi Jinping pointed out that no rules, no side round. Party

41、 constitution is the fundamental law, the party must follow the general rules. In early 2015 held the eighth session of the Central Commission for Discipline Inspection Fifth Plenary Session of the 16th Central Committee, Xi Jinping again pointed out that constitution is the party must follow the ge

42、neral rules, but also the general rules. the revision of the and is Method in adhere to the regulations established for the purpose of combining rule of virtue is to adhere to the party constitution as a fundamental to follow, the constitution authority set up, wake up the party constitution and par

43、ty rules the sense of discipline, the party constitution about discipline and self-discipline specific requirements. 4 second is to adhere to in accordance with the regulations governing the party and the party. The Party of rule of virtue de, mainly refers to the partys ideals and beliefs, excellen

44、t traditional style. The revised the closely linked to the self-discipline, insisting on the positive initiative, for all members, highlight the vital few, emphasized self-discipline, focusing on the morality, and the majority of Party members and the ideological and moral standards. The revised Ji method separately, Ji, Ji Yan to Method, as a negative list, emphasizing the heteronomy, focusing