SMF0710A主要保养项目检查表/Checking Report of Major Maintenance Items.doc
《SMF0710A主要保养项目检查表/Checking Report of Major Maintenance Items.doc》由会员分享,可在线阅读,更多相关《SMF0710A主要保养项目检查表/Checking Report of Major Maintenance Items.doc(3页珍藏版)》请在三一办公上搜索。
1、 SAFETY MANAGEMENT SYSTEM CHECKLIST/安全管理系统查核表主要保养项目检查表Checking Report of Major Maintenance Items船舶名称: (Ships Name) 上次日期: (Last Date)本次日期: (This Date)注: 1. 请于空格分别书明“良好”、“可”、“劣”及“检查日期”。Note Please fill all block detail mark Good, Fair, Poor and data respectively.2. 甲板部及机舱部的电气绝缘测试值(M)记录必须提供。Records of
2、megger test of all electric equipment for deck and engine department to be submitted.3. 本报告必须按每三个月送回公司一次,船上留存一份副本。This report must be sent to The Company every three months with a copy in ships file.1. 甲板机械设备Deck Machineries and Equipment1.1起锚机 Windlass:1.2绞缆机Mooring Winches:1.1.1. 油漆状况Condition of
3、coating1.2.1. 油漆状况Condition of coating1.1.2. 油压控制系统的状况Condition of hydraulic system1.2.2. 油压控制系统的状况Condition of hydraulic system1.1.3. 剎车板的状况Condition of break linings1.2.3. 剎车板的状况Condition of break linings1.1.4. 所有加油孔的加滑油日期Greasing date of all grease points1.2.4. 所有加油孔的加滑油日期Greasing date of all gre
4、ase points1.1.5. 控制器的齿轮剎车轮的加滑油日期Greasing date of open gears/break controller1.2.5. 控制器的齿轮剎车轮的加滑油日期Greasing date of open break/break controller1.3 导缆滚轮与巴拿马导索孔Fairleaders and Panama Chocks:1.4 货舱的通风筒Ventilator of Cargo Holds:1.3.1. 外观状况Condition of externality1.4.1. 外观状况Condition of externality1.3.2.
5、活动部份灵活度Whether moving part free1.4.2. 活动部份灵活度Whether moving part free1.3.3. 加滑油日期Date of greasing1.4.3. 加滑油日期Date of greasing1.5 水密门及盖Water Tight Doors and Covers:1.6 加水柜通气孔头Tanks Air Vent Heads:1.5.1. 绞链、手把及蝶彩螺拴等灵活度Whether hinges/handles/butterfly nuts free1.6.1. 管盖端盖板、螺栓等灵活度Whether flaps / check b
6、alls / covers & nuts free1.5.2. 加滑油日期Date of greasing1.6.2. 加滑油日期Date of greasing1.7 机舱及住舱的通风筒Ventilator of Engine Room & Accommodation:1.8 补给粮吊车Provision Crane:1.7.1. 外观状况Condition of externality1.8.1. 外观状况Condition of externality1.7.2. 阻板及菌形通风头灵活度Whether dampers & mushroom heads free1.8.2. 转动齿轮与滑车
7、的灵活度Whether turning gear, blocks free1.7.3. 上次保养及加滑油日期Date of last maintenance / greasing1.8.3. 上次保养及加滑油日期 Date of last maintenance / greasing1.7.4. 通风筒马达的绝缘测试日期Megger testing of motors; Date:1.8.4. 马达状况与绝缘测试值记录Motor condition & meg. test reading /M. Ohms附注Remarks:电气绝缘值测试由二管轮执行:The megger testing be
8、 done by 2/Engineer.2. 货舱口盖Cargo Hold Hatches2.1 除锈与油漆状况Condition of de-rusting & Coating2.2 水密性Whether watertight2.3 油压系统是否有漏油Any oil leaking of hydraulic systems2.4 油压管线的除锈与油漆状况De-rusting & Coating of hydraulic system2.5 油压训动器的灵活度Moving free of hydraulic jacks2.6 上次驱动齿轮传动炼传动网丝的保养日期Last maintenance
9、 of driving gears / Chains / wires2.7 导动轨导与压力板的状况Condition of railways & compression bars2.8 轮固定螺杆与螺帽的灵活度Moving free of wheels, cleats & nuts2.9 驱动绞车与剎车板的状况Condition of driving winches & breaklinings2.10 加滑油日期Date of greasing2.11 各货舱油压泵马达的电气绝缘测试值记录Date of megger testing & reading of motors:1.2.3.4.5
10、.附注Remarks:电气绝缘值的测试由二管轮执行:The megger testing be done by 2/Engineer. SAFETY MANAGEMENT SYSTEM CHECKLIST/安全管理系统查核表主要保养项目检查表Checking Report of Major Maintenance Items注: 1. 请于空格分别书明“良好”、“可”、“劣”及“检查日期”。Note Please fill all block detail mark Good, Fair, Poor and data respectively.2. 甲板部及机舱部的电气绝缘测试值(M)记录必须
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SMF0710A主要保养项目检查表Checking Report of Major Maintenance Items SMF0710A 主要 保养 项目 检查表 Checking

链接地址:https://www.31ppt.com/p-5050503.html