pa角钢插入式基础施工作业指导书.doc
《pa角钢插入式基础施工作业指导书.doc》由会员分享,可在线阅读,更多相关《pa角钢插入式基础施工作业指导书.doc(17页珍藏版)》请在三一办公上搜索。
1、evaluation of scientific development. Nature security type-nature security is to maintenance people of health value for target, through strengthening security based management, and risk management, and equipment management and technology supervision, ensure production in the people, and real, and sy
2、stem, and system, elements security reliable, and harmony unified, full control various against factors, achieved thought no slack, and management no empty document, and equipment no hidden, and system no blocked, and unit zero non-stopped. Quality and efficiency-quality benefit is to adhere to the
3、enterprise survival, profit and development business truth, adhere to the all activity is economic activity, all costs can be controlled, money should not be wasted management philosophy, management analysis, to improve management quality, improve cost control capacity and market competitiveness. In
4、novation of science and technology-science and technology innovation is to play the role of science and technology as the primary productive force, active use of new technologies, new materials, new processes, new equipment, increase investment in science and technology, strengthening scientific and
5、 technological training, speeding up transforming scientific and technological achievements, forming a number of proprietary technology, enhancing core competitiveness. Resource-saving-the-resources saving enterprise was to reduce coal consumption, water consumption, electricity at the core, enhance
6、 the operation of lean management to realize low consumption, high efficiency, reduce production costs. Second is to strengthen the business, financial, material, information and the optimization of organization and management, saving the internal transaction costs. Harmonious development of harmoni
7、ous development-is to construct a foreign environment for development. XING refers to the internal security firm and internal management of the internal management measures are effective, harmonious. Foreign currency means Enterprise coordinating development of homeopathy, well, get along with the n
8、eighbors better. (B) XX 2013 five enterprises building intrinsic safety power company goals are: unplanned outage 0 times. Class of disorders 0, 0 is equivalent forced outage rate. No personal injury accident, material and equipment accidents do not occur, no fire, no environmental pollution acciden
9、t. Enterprise integrated to achieve zero cases of violation, zero accidents, zero. Quality goal is: when generating capacity 7.5 billion-kilowatt, sales of over 7.11 billion kWh, total profits of 306.6 million Yuan, . BFS+、PI、MIS、SCM Information systems infrastructure, fully integrated information s
10、ystem to realize information resources sharing; to expand the breadth and depth of the portal system, information system of Enterprise Management Assistant role to play; to improve the day-to-day operation and maintenance operation record of promoting causes and transfer system; to strengthen the tr
11、aining主角钢插入式角钢基础施工作业指导书 贵州送变电工程公司1 一规定和引用文件1.1范围本作业指导书适应于110-500kV架空电力线路铁塔基础施工。1.2一般规定1.2.1 所用的模板应符合“模板工程作业指导书” 的要求;其它材料应符合送电专业现浇混凝土工程作业指导书一般规定的要求。1.3引用文件100-500kV架空电力线路施工及验收规范(GBJ23390)建筑工程施工质量验收统一标准(GB50300-2001,TAB0531)混凝土结构工程施工质量验收规范(GB50204-2002,TAB-0543)普通混凝土用砂质量标准及检验方法(JGJ52-92)普通混凝土用碎石或卵石质量标
12、准及检验方法(JGJ53-92)电力建设安全工作规程(架空电力线路部分)(DL5009-2-94)CX/QSB16.01-2001质量记录的控制程序。2 主要工器具配置序号名称规格型号单位数量备注1经纬仪TDJ2套1含塔尺、钢尺等2搅拌机卧式台13振动棒台2配汽油机,最好用电动4手推车台65凿岩机台1条件好用空压机6铁板2米1米块83 劳动组织序号岗位人数备注1指 挥12测 工15机操工1分别负责搅拌机6民 工254 主角钢悬浮插入式基础简介主角钢插入式基础是将与铁塔主材规格相同的角钢直接斜插入立柱的混凝土,与砼浇制成一体,省去地脚螺栓、塔脚等,以节省钢材。基础立柱一般为等截面斜柱,顺铁塔主材
13、坡度布置,主角钢多数悬浮于基础立柱中,如下图(1)、图(2)所示外形尺寸及立柱。主角钢坡度随塔型,塔腿坡度的变化而变化。 接辅助角钢图1 图2插入角铁在立柱顶面位置如下图(3): L A 图(3) A值为基础顶面上插入角钢外边缘至基础中心的距离,由设计给出。插入角钢露出基础顶面长度也由设计给出。主角钢插入式基础施工特点:主角钢必须在基础中高精度定位,包括根开尺寸、角钢倾角,各腿高差等都必须准确无误,否则将影响组塔施工。5 施工工艺流程图施工准备测量分坑基础坑开挖及检查钉立基础控制桩安装及校正主角钢绑扎基础钢筋支模板浇制混凝土检查基础几何尺寸、主角钢倾斜及扭转施工结束6 施工准备6.1异型模板的
14、设计及加工6.1.1异模板的设计原理一般情况下,为了施工方便,基础底盘均以土或石壁代替模板,所以异形模板设计只针对立柱。由于主角钢插入式基础为立柱为等截面斜柱,主柱侧面为平行四边形,应根据不同的基础型式制作相应的异型模板。主柱表面展开如下图: B A C D 标准 标准 标准 标准模板 模板 模板 模板 A B D C 其需要由标准模板和异型模板拼装而成;主体部份由标准钢模板组成,上下边由异形钢模板拼装而成,图为A、B、C、D面。对同一种基础型式而言,异型模板A与C、B与D的几何尺寸相同的,只是模板边与加强铁焊接面不同而已,一个基础腿A、B、C、D异型模板各两块。6.1.2异型模板尺寸计算要确
15、定异型模板的几何尺寸,必须先计算出等截面立柱侧面的几何尺寸,从中等距离截取能用标准模板拼装的部分后,剩余部分即为异模板拼装部分。将基础主柱延伸至底板下平面,其立柱图形如下图: B C O A D B1 C1 F K L G图5 A1 I D1 K1 O1 E I1 H A、B、C、D为主柱上平面、A1、B1、C1、D1为主柱下平面,立柱延伸至底板下平面交于E、F、G、H点。O为主柱上平面中心、L为主柱下平面中心、O1为底板下平面中心;由A点向下作垂线,交A1L于K点、交EO1于K1点,由A点向A1D1作垂线交于I点,由K1点向EH作垂线交于I1点,则AI垂直于A1D1,AI1垂直于EH。设计给
16、出的已知条件如下:EI1=a 立柱上平面中心偏离底盘中心的正面水平偏移值;AK=h 基础立柱高;AK1=h1 基础全高;基础立柱侧面几何尺寸计算如下:EK1=2 a (图中EK1I1为等腰三角形)=tg-1h1/ (2a)AE=h1/sin sin=h1/AE (AEK1三角形)=1=cos-1(a/AE ) (在AEI1三角形中=1=cos-1(a/AE))根据相似三角形原理:AA1/AE=h/h1; AA1=hAE/h1以上求出AA1及角度,基础立柱侧面几何尺寸即确定,随之异型模板尺寸即可确定。根据具体工程使用的基础型式及基础腿数,从而确定异形钢模板的加工数量。7 施工步骤7.1测量分坑7
17、.1.1分坑数据计算:主角钢插入式基础主柱顶面中心与底面中心存在相对位移,同时一般线路设计采用全方位高低腿且为正方形根开,分坑时,四个塔腿须分别测定,设计一般给出塔位基础四个腿的根开值,分坑时须根据所给基础型式计算底盘的半根开和半对角线根开值,从而确定坑口尺寸。7.1.2正方形根开主角钢插入式基础分坑方法(对角线法)如下图(6): A D E1 E B C LO中心桩 图(6)图(6)中L为底盘宽度,E为立柱上平面中心、E1为底盘中心。底盘半对角线根开值OE1=OE+EE1;上式中OE为基础根开值,EE1为立柱上平面中心沿对角线方向偏离底盘中心值; EE1=2 a (a值设计已给出)确定OE1
18、值后,根据基础型式可求出OB、OD的值,用尺则可定出A、C点位置。7.2基础坑开挖及检查基础坑根据地质情况,采用人工开挖或爆破开挖,基坑开挖完后,必须对坑位方向、距离、坑口上、下部尺寸和坑深进行检查,避免尺寸不符合设计要求而影响施工。7.3测量方法根椐设计发展方向,基础一般采用全方位高低腿,同一基铁塔中心距各塔腿基础顶面高差往往较大,基础分坑定位时,一般采用角度测斜距的方法:经纬仪支于线路中心桩上,沿线路方向转45测出该点对另一点的垂直角,用钢皮尺直接量出仪器中心点到该点的斜距S,再计算出水平距离L见图(7): L=Scos S a L图(7)当测量方向上有凸物,不通视时,一般通过多次分段测量
19、再累计的方法确定距离;障碍物不是很高,地质为土或土夹石时,建议开测量槽,因为分段测量,移动仪器,误差随之增大。7.4主角钢插入式基础定位控制桩的钉立 控制桩必须钉在坑中附近且不易被撞动的地方,控制桩的高度必须保证为主角钢露出高+200mm以上的操作高度;见控制桩示意图(8),其中A、B、C、D、E、F六个桩均应操平,G为立柱顶部中心;A、B、C、D四个桩用来控制立柱顶部模板位置。E、F桩控制主角钢的位置尺寸及倾斜。 D F D A G C E B图(8)7.5安装固定插入式主角钢7.5.1斜插主角钢安装尺寸计算见下图(9)、(10): b E H E2 a1 E1 E1 E b a1 O O图
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- pa 角钢 插入 基础 施工 作业 指导书
链接地址:https://www.31ppt.com/p-4792890.html