CAN 协议毕业论文外文翻译.doc
《CAN 协议毕业论文外文翻译.doc》由会员分享，可在线阅读，更多相关《CAN 协议毕业论文外文翻译.doc（10页珍藏版）》请在三一办公上搜索。
1、附录二 文献翻译CAN protocol M .J .SchofieldThe CAN protocol is an international standard defined in the ISO 11898. Beside the CAN protocol itself the conformance test for the CAN protocol is defined in the ISO 16845, which guarantees the interchangeability of the CAN chips.1. Principles of data exchangeCAN
2、 is based on the “broadcast communication mechanism”, which is based on a message-oriented transmission protocol. It defines message contents rather than stations and station addresses. Every message has a message identifier, which is unique within the whole network since it defines content and also
3、 the priority of the message. This is important when several stations compete for bus access (bus arbitration). As a result of the content-oriented addressing scheme a high degree of system and configuration flexibility is achieved. It is easy to add stations to an existing CAN network without makin
4、g any hardware or software modifications to the present stations as long as the new stations are purely receivers. This allows for a modular concept and also permits the reception of multiple data and the synchronization of distributed processes. Also, data transmission is not based on the availabil
5、ity of specific types of stations, which allows simple servicing and upgrading of the network.2. Real-time data transmissionIn real-time processing the urgency of messages to be exchanged over the network can differ greatly: a rapidly changing dimension, e.g. engine load, has to be transmitted more
6、frequently and therefore with less delays than other dimensions, e.g. engine temperature. The priority, at which a message is transmitted compared to another less urgent message, is specified by the identifier of each message. The priorities are laid down during system design in the form of correspo
7、nding binary values and cannot be changed dynamically. The identifier with the lowest binary number has the highest priority. Bus access conflicts are resolved by bit-wise arbitration of the identifiers involved by each station observing the bus level bit for bit. This happens in accordance with the
8、 wired-and-mechanism, by which the dominant state overwrites the recessive state. All those stations (nodes) with recessive transmission and dominant observation lose the competition for bus access. All those losers automatically become receivers of the message with the highest priority and do not r
9、e-attempt transmission until the bus is available again. Transmission requests are handled in order of their importance for the system as a whole. This proves especially advantageous in overload situations. Since bus access is prioritized on the basis of the messages, it is possible to guarantee low
10、 individual latency times in real-time systems.3. Message frame formatsThe CAN protocol supports two message frame formats, the only essential difference being in the length of the identifier. The “CAN base frame” supports a length of 11 bits for the identifier, and the “CAN extended frame” supports
11、 a length of 29 bits for the identifier. 4. CAN extended frame formatThe difference between an extended frame format message and a base frame format message is the length of the identifier used. The 29-bit identifier is made up of the 11-bit identifier (“base identifier”) and an 18-bit extension (“i
12、dentifier extension”). The distinction between CAN base frame format and CAN extended frame format is made by using the IDE bit, which is transmitted as dominant in case of an 11-bit frame, and transmitted as recessive in case of a 29-bit frame. As the two formats have to co-exist on one bus, it is
13、laid down which message has higher priority on the bus in the case of bus access collision with different formats and the same identifier / base identifier: The 11-bit message always has priority over the 29-bit message. The extended format has some trade-offs: The bus latency time is longer (in min
14、imum 20 bit-times), messages in extended format require more bandwidth (about 20 %), and the error detection performance is lower (because the chosen polynomial for the 15-bit CRC is optimized for frame length up to 112 bits). CAN controllers, which support extended frame format messages are also ab
15、le to send and receive messages in CAN base frame format. CAN controllers that just cover the base frame format do not interpret extended frames correctly. However there are CAN controllers, which only support the base frame format but recognize extended messages and ignore them.5. Detecting and sig
16、naling errorsUnlike other bus systems, the CAN protocol does not use acknowledgement messages but instead signals errors immediately as they occur. For error detection the CAN protocol implements three mechanisms at the message level (data link layer: OSI layer 2): Cyclic Redundancy Check (CRC): The
17、 CRC safeguards the information in the frame by adding a frame check sequence (FCS) at the transmission end. At the receiver this FCS is re-computed and tested against the received FCS. If they do not match, there has been a CRC error. Frame check: This mechanism verifies the structure of the transm
18、itted frame by checking the bit fields against the fixed format and the frame size. Errors detected by frame checks are designated format errors. ACK errors: Receivers of a message acknowledge the received frames. If the transmitter does not receive an acknowledgement an ACK error is indicated. The
19、CAN protocol also implements two mechanisms for error detection at the bit level (physical layer: OSI layer 1): Monitoring: The ability of the transmitter to detect errors is based on the monitoring of bus signals. Each station that transmits also observes the bus level and thus detects differences
20、between the bit sent and the bit received. This permits reliable detection of global errors and errors local to the transmitter. Bit stuffing: The coding of the individual bits is tested at bit level. The bit representation used by CAN is Non Return to Zero (NRZ) coding. The synchronization edges ar
21、e generated by means of bit stuffing. That means after five consecutive equal bits the transmitter inserts a stuff bit into the bit stream. This stuff bit has a complementary value, which is removed by the receivers. If one or more errors are discovered by at least one station using the above mechan
22、isms, the current transmission is aborted by sending an error frame. This prevents other stations from accepting the message and thus ensures the consistency of data throughout the network. After transmission of an erroneous message that has been aborted, the sender automatically re-attempts transmi
23、ssion (automatic re-transmission). Nodes may again compete for bus access. However effective and efficient the method described may be, in the event of a defective station it might lead to all messages (including correct ones) being aborted. If no measures for self-monitoring were taken, the bus sys
24、tem would be blocked by this. The CAN protocol therefore provides a mechanism to distinguish sporadic errors from permanent errors and local failures at the station. This is done by statistical assessment of station error situations with the aim of recognizing a stations own defects and possibly ent
- 配套讲稿：
如PPT文件的首页显示word图标，表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制：
部分文档作品中含有的国旗、国徽等图片，仅作为作品整体效果示例展示，禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词：
- CAN 协议 毕业论文外文翻译 毕业论文 外文 翻译
三一办公所有资源均是用户自行上传分享，仅供网友学习交流，未经上传用户书面授权，请勿作他用。
wu基坑开挖引起土体侧移对桩的影响.docwu基坑开挖引起土体侧移对桩的影响.doc
ASP简介毕业论文外文翻译.docASP简介毕业论文外文翻译.doc
JSP 应用框架毕业论文外文翻译.docJSP 应用框架毕业论文外文翻译.doc
S7200的特性毕业论文外文翻译.docS7200的特性毕业论文外文翻译.doc
毕业论文外文翻译(原文).doc毕业论文外文翻译(原文).doc
ASP.NET 技术毕业论文外文翻译.docASP.NET 技术毕业论文外文翻译.doc
DSP的发展毕业论文外文翻译.docDSP的发展毕业论文外文翻译.doc
PLC的控制优势毕业论文外文翻译.docPLC的控制优势毕业论文外文翻译.doc
一种基于带有特别的过滤和偏移调制的光栅投影的位移传感器毕业论文外文翻译.doc一种基于带有特别的过滤和偏移调制的光栅投影的位移传感器毕业论文外文翻译.doc
BBS的发展史毕业论文外文翻译.docBBS的发展史毕业论文外文翻译.doc
链接地址：https://www.31ppt.com/p-3931448.html