ASME焊材管理程序.doc
《ASME焊材管理程序.doc》由会员分享,可在线阅读,更多相关《ASME焊材管理程序.doc(5页珍藏版)》请在三一办公上搜索。
1、Zhenjiang JinMen Industrial Co., LtdASME ProceduresJM/ASME-04Welding Material Control ProcedureRev. No.: 0.0Page:1 of 5Welding Material Control Procedure 焊 接 材 料 管 理 程 序 Prepared by Date _ 编 制: 日期:Approved by _ Date _ 批 准: 日期:Accepted by _ Date _ 认 可: 日期:Zhenjiang JinMen Industrial Co., LtdASME Proc
2、eduresJM/ASME-04Welding Material Control ProcedureRev. No.: 0.0Page:2 of 51Scope 范围1.1This procedure provides supplementary requirements to the QC Manual and “General Material Control Procedure” (JM/ASME-02)about the storage, baking, issuance and return of welding consumables used for construction o
3、f ASME Code items. 本程序规定了质量管理手册和材料控制程序的关于用于制造ASME规范产品的材料的存储、烘干、发放和返还焊材的补充要求JM/ASME-02。2Receiving Inspection of Welding Consumables 焊材的接收检验2.1QC Engineer shall provide sufficient training and knowledge to the Material Keeper about the welding consumables control requirement in the QC Manual. The Mate
4、rial Keeper shall be familiar with the general requirements and specifications of welding materials. 质量控制工程师应为材料保管员提供在质量管理手册上关于焊材控制要求的足够的训练和知识。材料保管员应熟悉总则的要求和焊材规范。2.2When receiving welding consumables, the Material Keeper shall check and verify welding consumable as per “Material Requisition”. He sha
5、ll check the marking of the welding consumable container in accordance with the applicable specifications. He shall also inspect the condition of packing in order to assure that no damage has been occurred. 当接收焊材时,材料保管员应根据材料申请单检查和检验焊材。他应根据适用的规范检查装焊材的容器。为了确保没有损坏发生,他应检查包装的情况。材料保管员只能对焊材的外观、数量、批号、牌号进行检验
6、,对焊材内部质量的检验应由材料检验员进行检验,而不应由保管员进行检验。3Storage of Welding Consumables 焊材的储存3.1Welding materials shall be stored in such the way as specified in the General Material Control Procedure. 焊材应按照材料管理程序的要求被储存。3.2The welding materials for Code items shall be stored in the designated shelves of 12 in. (300 mm)
7、away from the wall and above the floor under controlled temperature (30C + 10C) and humidity (less than 60%). The Material Keeper shall prevent intermingling materials of different specification, brands and lots, and shall make correct marking. Welding materials shall be protected from damage, loss
8、or deterioration. The Material Keeper shall assure that appropriate storage conditions are maintained. Zhenjiang JinMen Industrial Co., LtdASME ProceduresJM/ASME-04Welding Material Control ProcedureRev. No.: 0.0Page:3 of 5符合规范的焊材应被储存在12英寸(300mm)的指定架子上,远离墙壁和地板,室温保持在(30C + 10C)和相对湿度(小于60%)。焊材的材料保管员应防止
9、不同规范、品牌、批次的材料相混合,保持标识的正确性。焊材应防止损坏、丢失、或腐蚀。材料保管员应确保维持适宜的储存条件。3.3The store-house of welding materials shall be furnished with proper facilities for storing. If applicable, these facilities shall be calibrated and controlled as per the requirement of QC Manual. The Material Keeper shall be responsible f
10、or receiving, storing, baking and issuing welding materials, and maintaining the records. 储存焊材的仓库应配有适当的设备以维持需要的储存条件。适当时,这些设备应被校验,并按照质量管理手册的要求进行控制。材料保管员应负责接收、储存、烘干和发放焊材,并维持记录。在使用前,覆盖着的电极和焊剂应按照技术规范、焊材制造厂的建议和规范对其进行干燥处理。3.4The Material Keeper shall check and verify the temperature and humidity in the st
11、ore-house twice a day. 材料管理员应在一天内检测和确认仓库的温度和湿度两次。4Drying and Holding 烘干和储存4.1Prior to using, electrodes and flux shall be dried in accordance with the general recommendation as specified in Table 1.在使用之前,焊条和焊剂都应根据表1的要求进行烘干。4.2The dried electrodes shall be kept in the holding oven and held at 212F to
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASME 管理程序
![提示](https://www.31ppt.com/images/bang_tan.gif)
链接地址:https://www.31ppt.com/p-3881580.html