智能照明控制系统 外文翻译.docx

《智能照明控制系统 外文翻译.docx》由会员分享，可在线阅读，更多相关《智能照明控制系统 外文翻译.docx（13页珍藏版）》请在三一办公上搜索。

1、智能照明控制系统 外文翻译中文2500字 本科毕业设计 题 目 基于PWM的智能多功能台灯设计 姓 名 专 业 自动化 学 号 指导教师 二一四年五月外文翻译 Intelligent lighting control system Abstract: Intelligent lighting control system the main aim is to save energy, smart lighting control system with a variety of pre-set control mode and control components, at different

2、times on different degrees of illumination for accurate set-up and rational management of energy-saving. This automatic adjustment of the illumination means, take full advantage of the natural outdoor light, only when necessary when the lamp or light to the required brightness, use the least energy

3、to ensure that the required illumination level, energy-saving effect is very clear, usually ranging from more than 30%. Keywords: Intelligent lighting control system bus-type star-shaped structure 1 The advantages of the use of the intelligent lighting control system 1.1 Good energy saving effect In

4、telligent lighting control system using the main purpose is to save energy, smart lighting control system with a variety of pre-set control mode and control components, at different times on different degrees of illumination for accurate set-up and rational management of energy-saving. This automati

5、c adjustment of the illumination means, take full advantage of the natural outdoor light, only when necessary when the lamp or light to the required brightness, use the least energy to ensure that the required illumination level, energy-saving effect is very clear, usually ranging from more than 30%

6、. In addition, the intelligent lighting control system for fluorescent lamp dimming control, etc., due to the use of a fluorescent active tunable filter electronic ballast technology and reduce the harmonic content, to improve the power factor and reduce the low-voltage reactive power loss. 1.2 To e

7、xtend the life span of light source 1 外文翻译 Light source can not only extend the life savings, but also significantly reduce the workload of lamp replacement, reducing the operating costs of lighting systems, management and maintenance becomes simple. Both the thermal radiation source, or gas dischar

8、ge light source, voltage fluctuations are a major cause of light damage. Therefore, the effective suppression of the fluctuations in voltage can extend the life of light sources. Intelligent lighting control system can successfully suppress the surge voltage power grid, but also have a voltage limit

9、 and the conjugate stream functions of filtering, to avoid over-voltage and under-voltage damage to the light. The use of soft-start and soft turn-off technology, to avoid the impact of current damage to the light. Through this method, the light source to extend the life span of usually 2 to 4 times

10、. 1.3 To improve the working environment improve efficiency Good working environment is to improve the efficiency of a necessary condition. Good design and reasonable choice of light source, lamps and lighting quality control systems, can improve the quality of lighting. Intelligent lighting control

11、 system dimming control panel module to replace the traditional lighting of the level switch control is an effective way to control the overall room illumination value, thereby enhancing the uniformity of illumination. At the same time, this control method used in electrical components have also sol

12、ved the stroboscopic effect, will not create uncomfortable, confused, feeling eyestrain. 1.4 To achieve a variety of lighting effects A wide range of lighting control, the same building can have a variety of artistic effect, for a lot of construction hyperchromic. Modern buildings, lighting is not s

13、imply to meet people on the visual effect of light and shade, they should have control of a variety of programs to make buildings more vivid, more artistic, giving a wealth of visual effects and aesthetics. As an example of a project, building the exhibition hall, lecture hall, lobby, atrium, etc.,

14、if with intelligent lighting control system, according to different times, different uses, different effects, using the 2 外文翻译 corresponding pre-set scene control, can achieve the wealth of artistic effect. 1.5 Facilitate the management of maintenance Intelligent lighting control system for the cont

15、rol of lighting based on the automatic control of modular-based, supplemented by manual control, preset lighting scenes to the parameters stored in the EPROM Digital, these information is very convenient to set up and replaced, so that building lighting management and maintenance easier. 1.6 Have a

16、high economic rate of return Our reference point for the Shanghai region, from energy-saving lights and provincial estimates of the two made a come to this conclusion: with three to five years, the owner can recover the basic intelligent lighting control system to increase the total costs. Intellige

17、nt lighting control system can improve the environment and improve employee productivity and reduce maintenance and management costs, but also for the owners to save a substantial amount of costs. 2 Intelligent lighting control system components We know that the intelligent lighting control system o

18、f building control system is onlyone part of the. If you want to focus on the various control systems to the control center to control, then the control system must have the standard communication interface and protocol version. Although such a system integration is feasible in theory, but it is ver

19、y difficult to put into practice. Thus, in engineering, intelligent management of our building a distributed system, distributed, that is relatively independent of each control subsystem, self-contained, the implementation of specific control, intelligent building management system control subsystem

20、 of the relative independence, self-contained, the implementation of specific control, intelligent building management system from the control subsystem is a signal collection and monitoring role. At present, the intelligent lighting control system in accordance with sub-network topology, the follow

21、ing two forms, namely, bus and 3 外文翻译 star-shaped structure-based hybrid. Both forms have the characteristics of a number of bus more flexibility, easy expansion, control of relative independence, lower costs; mixed some high reliability, fault diagnosis and rule out the simple, easy access to the a

22、greement, transfer rate higher. Engineering design, we consider the building of intelligent lighting control system as an independent subsystem, use of international standards and agreements of the communication interface text, into the intelligent building management systems. Intelligent lighting c

23、ontrol system uses a distributed, distribution-based approach,that is, the dimming control unit is relatively independent, self-contained,non-interfering, through centralized management and information interfaces, and intelligent building management system linked to the achievement of the building c

24、ontrol center subsystem of the collection and monitoring of the signal. In short, the intelligent lighting control should be the main system is a centralized management, and the main trunk and information interface components consisting of the regional implementation of the same sample of control an

25、d signal networks; its subsystems should be a dimmer by the various types of modules , control panels, illumination detector dynamic and static and dynamic components consisting of detectors, respectively, of the regional implementation of the specific control of different networks, the main system

26、and subsystems, such as between the components through the interface to connect, to achieve data transmission. 3 Intelligent lighting control system and control of the control of the content A project to control the use of intelligent lighting control system include the following categories: technol

27、ogy office hall, computer center and other important room, lecture hall, such as multi-function hall, exhibition hall, conference center, lobby and courtyard, walkways and elevators, such as the Office of Public site; building facade lighting ingeneral and also by the intelligent lighting control sy

28、stems to control switch signal. Control the content of the term of the Interpretation: 1 clock 4 外文翻译 control Clock management, etc. through the electrical components, to achieve the normal work of regions for the state of lighting in different time control. 2 the automatic adjustment control illumi

29、nation Through each module and illumination dimming dynamic electrical components such as detectors, to achieve under normal conditions in the regions for the normal work of the state of the automatic lighting dimming control, making the region, such as illumination will not be outside with the suns

30、hine factors change, and always maintain the default value in the illumination around. 3 control of the regional scene Through each dimmer module and the control panel and other electrical components, to achieve under normal conditions in the regions for the normal work of the state of the scene lig

31、hting control switch. 4 static and dynamic detection of control Through each dimming modules and electrical components, such as movement detectors, to achieve under normal conditions in the regions for the normal work of the state of the automatic lighting control switch. 5 Reduction state of emerge

32、ncy control Through each of the normal lighting control module, such as dimming of the electrical components, to achieve a state of emergency for the normal work of the various districts in the state of lighting and to give up the number of relief, such as dimming control. 6 Manual remote control Th

33、rough the infra-red remote control, to achieve under normal conditions in the regions for the normal work of the state of lighting control and manual control of the regional scene. 7 Emergency lighting control Here mainly refers to the control of intelligent lighting control system to the special re

34、gion by the implementation of the emergency lighting control, including the following two controls: 1 under normal illumination and the automatic adjustment control of the regional scene with the regulation of the normal work of lighting the same manner as the control. 2 a state of emergency automat

35、ic discharge dimming control, through each of the emergency lighting dimming control module, such as electrical components, to achieve a state of emergency for the regions under a state of emergency lighting dimmers, such as giving up control, so that the accident in the state of emergency lighting

36、to reach 100%. These are the characteristics of intelligent lighting control systems analysis and office buildings in a specific application in a number of experiences, hoping to 5 外文翻译 play the role of forward, so that the field of technology in the lighting to fully play its role. 6 外文翻译 智能照明控制系统

37、摘要:智能照明控制系统的主要目的是利用“预先设定的“控制方式和控制元件对照明系统进行优化管理,智能照明控制系统在不同时期,不同程度上的照明进行精确设置和合理的节能管理。这种自动调整的照明方式,充分利用室外的自然光,只在必要时当灯或灯光亮度有特殊要求时,用最少的能源,在确保所需的照明度的前提下,达到理想的节能效果,一般可达30%以上。 关键词:智能照明控制系统 总线型 星型结构 1 利用智能照明控制系统的优势 1.1 良好的节能效果 智能照明控制系统的主要目的是节约能源,智能照明是用“预先设定的“控制模式和控制元件的控制系统,在对不同时间的不同光照度进行准确的设置和合理的节能管理。这种自动调整照

38、明方式,采取充分利用室外的自然光,只在必要时当灯或光所需的亮度有要求时,用最少的能源,以确保所需的照明度,节能效果十分明显,通常是超过30%不等。此外,智能照明荧光灯调光控制灯等,由于使用荧光灯电子镇流器有源可调谐滤波器技术,减少了谐波含量,提高了功率因数,降低了低压无功损耗。 1.2 延长光源寿命 照明光源不仅可以延长使用寿命,而且还大大减少更换灯泡的工作量,减少照明系统的运作成本,使得管理和维修变得简单。 无论是热辐射光源或是气体放电光源,电压波动是光损伤的重要原因。因此,有效的制止波动电压可以延长光源的寿命。 智能照明控制系统可以成功地抑制电源网络的浪涌电压,但也有限制电压和共轭电流滤波

39、的功能,以避免过电压和欠电压损坏光源。通过使用软启动和使用软关断技术,可以避免损害到光电源。通过这种方法,光源寿命通常可延长为2至4倍。 7 外文翻译 1.3 改善工作环境,提高工作效率 良好的工作环境,是提高效率的一个必要条件。良好的设计和光源,灯具和照明质量控制系统的合理选择,可以提高照明质量。 智能照明控制系统使用的调光控制面板模块,用以取代传统的液位开关控制照明是一种有效的方式来控制整个房间照度值,从而提高照度均匀性。同时,这种控制方法在电器元件使用,也解决了频闪效应,也不会产生不舒服的,混乱的感觉和眼睛疲劳。 1.4 实现了多种灯光效果 一个广泛的照明控制,同样的建设可以有不同的艺术

40、效果并为建筑增色不少。现代建筑,照明不仅是为了履行对光影的视觉效果,设计师们应该有多种方案的控制,使建筑物更加生动,更加美观,给人一种视觉效果和美学的财富。作为一个工程实例,例如展厅,报告厅,大堂,中庭等,如果能利用智能照明控制系统,对不同时期,不同用途,不同的效果采用相应的预设置场景控制,就可以实现丰富的艺术效果。 1.5 便于维护管理 智能照明控制系统的控制基础为自动照明控制模块,由人工控制为辅,把预置的灯光场景的参数存储在EPROM中,这些信息可以非常方便的设置和更换,使建筑照明管理和维护更加容易。 1.6 具有较高的经济回报率 我们以上海地区为参考,从节能灯和省级这两个估计作出得出这样

41、的结论:三至五年,业主可以恢复基本智能照明控制系统的投资,以后便可以增加收入。 智能照明控制系统可改善环境和提高员工的工作生产率和降低维护和管理成本,而且还为业主节省了大量费用。 2 智能照明控制系统组件 我们知道,楼宇控制系统只是智能照明控制系统一个部分。如果你想专注于各种控制系统,控制中心控制,则控制系统必须具有标准通讯接口和协议的版8 外文翻译 本。虽然这样的系统集成在理论上是可行的,但它是非常难以付诸实践。因此,在工程中,我们建立一个分布式系统,所谓分布式,即各控制子系统相对独立的智能化,自我包含具体的控制,智能楼宇管理系统相对独立自足,控制子系统实现具体的控制,从控制子系统的智能化楼

42、宇管理系统的实施是一个信号收集和监测作用。 目前,智能照明控制系统按照网拓扑结构可以分为以下两种形式,即总线式和星形结构。这两种形式有更大的灵活性,易于扩展的数量特征,控制的相对独立性,成本低,高可靠性,故障诊断和排除简单,方便的协议,传输速率更高。 工程设计中,我们考虑了智能照明控制系统建设作为一个独立的子系统,采用国际标准和协议使用通讯界面文本进入智能建筑管理系统。智能照明控制系统是采用分布式,并以配送为基础的方法,即调光控制单元相对独立,自成体系,互不干扰,通过集中管理和信息接口,智能楼宇管理系统与建筑物的控制子系统实现收集中心和监测信号测功能。总之,智能照明控制应是一个集中管理,由主干

43、线和信息界面部分组成的控制区域执行信号网络,它的子系统,应该是一个由各类调光模块,控制面板,照明探测器动态和静态和动态组件组成的,分别对控制区域的具体实施不同网络,主系统和子系统,如组件之间,通过接口连接,实现数据传输。 3 智能照明控制系统和控制内容的控制 一个项目控制的智能照明控制系统的使用包括以下内容类别:科技办公大厅,计算机中心,报告厅等多功能厅,展览厅,会议中心,大厅和庭院,走廊和电梯等公共现场办公;大厦外墙一般照明并且由智能照明控制系统,以控制开关信号。 控制所包含的内容: 时钟控制 时钟管理,通过电器元件等,以达到在不同的地区正常工作状态的照明时间控制。 自动调整控制照明 通过每

44、个模块和动态调光照明电器元件等作为探测器,在正常条件下实现地区的自动调光控制使该地区照明状态正常工作,如果照明不随外面的阳光因素的变化,并始终保持在默认值照明左右。 控制的区域现场 通过每个调光模块和控制面板和其他电器部件,实现场景灯光控制开关状态正常工作。 静态和动态检测控制 通过每个调光模块和电气元件,如运动,探测器,实现自动照明控制开关状态正常工作。 应急控制 通过各种正常的灯光控制模块,如电气调光,组件,实现了各区紧急状态下的照明状正常工作。 手动遥控器 透过红外线遥控器,以达到在9 外文翻译 正常条件下对该地区的照明控制状态正常工作和手动控制区域场景。 应急照明控制这里主要指智能照明控制系统控制的特殊地区由应急照明控制,包括以下两个控件的实现: (1)在正常照明和区域自动调节控制 (2)随着场景的不同,照明控制方式也不同。 (3)通过对每个国家的紧急自动调光控制,应急照明调光控制模块,如电器元件,以实现下一个应急照明调光器,A国对地区进入紧急状态,如放弃控制权,从而使在事故应急照明状态达到100%。这是智能照明控制系统的分析和特点,希望能发挥前锋的作用,使技术在照明领域,充分发挥其作用。 10