常用塑胶英文单词.docx

《常用塑胶英文单词.docx》由会员分享，可在线阅读，更多相关《常用塑胶英文单词.docx（6页珍藏版）》请在三一办公上搜索。

1、常用塑胶英文单词嵌件-insert 嵌件銷-insert pin 氣脹真空成形-air assist forming 空氣隙-air gap 空氣頂出-air ejection 永久伸長-permanent elongation,tension set 永久變形-permanent set,permanent deformation 蝕刻,侵蝕-etching 應力-stress 應力鬆弛-stress relaxation 應力龜裂-stress cracking 應力集中-stress concentration 應力斷裂,應力破壞-stress rupture 應力.應變曲線-stres

2、s-strain curve 應力.應變圖-stress-strain diagram 托板,模板-retainer plate 硬度-hardness 合模機構-mold clamping mechanism 合模力,閉模力-locking force,clamping force 開模力-mold opening force 懸臂樑-cantilever beam 潤滑劑-lubricant 模具-mold,Tools,Tooling 模溫度控制器-mold temperature controller 模具尺寸-mold size 加熱管套(料筒)-heating cylinder 加熱

3、板-heating plate 凸輪-cam 玻璃纖維-glass fiber,fibrous glass 玻璃纖維強化熱塑塑膠-fiber glass reinforced thermoplastics,FRTP,glass fiber reinforced thermoplasitcs,GRTP 玻璃纖維強化塑膠-glass fiber reinforced plastics,GRP,fiber galss reinforced plastics,FRP. 感光聚合物-photopolymer,photo-sensitive polymer 鏡面拋光-mirror polishing 龜裂

4、-cracking 龜裂-crack 顆粒料-granule 石墨-graphite 石墨纖維-graphite fiber 間隙, 隙距-clearance 模蕊,蕊片,蕊線,蕊孔-core 成孔銷,模蕊銷-core pin 成孔銷托板-core pin plate 公差,容差-tolerance 冷料-cold slug 冷料井,冷料窩-cold slug well 回程銷,覆歸銷-surface pin 冷熱驟變試驗-thermal shock test 熱應力龜裂-thermal stress cracking,TSC 側向澆口-side gate 側向模蕊(心型)銷-side dra

5、w pin 砂磨-sanding 噴砂,打砂-sand blast 修飾,塗飾,打光-finishing 自斷澆口,剪切澆口-shear gate 紫外線-ultraviolet, UV 常用塑膠英文單詞 紫外線穩定劑-UV stabilizer 紫外線吸收劑-UV absorber 壓花-embossing 壓花機-embossing machine 噴霜,起霜-blooming exudation 鯊皮斑-shark skin 射出壓力-injection pressure 射出成形-injection molding 射出成形機-injection molding machine 射出成

6、形模具-injection mold 射出裝置-injection unit 射出速度-injection speed 射出噴嘴,注料嘴-injection nozzle 射出容量-machine shot capacity 射出率(量)-injection rate 煮沸試驗-boiling test 充填不足,缺料-short shot 手動模具-hand mold,loose mold 手動油壓機-hand press 縮窩,凹孔-shrinkage pool 衝擊試驗-inpact test 衝擊強度-impact strength 燒結法,粉鑄法-sintering 燒結成形法-si

7、nter molding 模板-mold plate 注射,射料-shot 矽橡膠-silicone rubber 真空成形-vacuum forming 珠光顏料-pearlescent pigment 浸漬塗裝-dip coating 人造皮革-artificial leather 廢料粉碎機-scrap grinder 頂出板,脫模板-stripper plate 應力龜裂-stress cracking 環境應力龜裂試驗-environmental stress cracking test 行程,衝程-stroke 注道,注道料-sprue 注道襯套,澆口襯套-sprue bush 成

8、形壓力,模製壓力-molding pressure 成形溫度,模製溫度-molding temperature 成形循環,成形週期-molding cycle 成形時間,模製時間-molding time 成形收縮,模壓收縮-mold shrinkage, molding shrinkage 窄澆口,限制形澆口-restricted gate 剪切強度,抗剪強度-shear strength 增亮劑-brightening agent,optical brightener,optical whitening agent 加速試驗-accelerated test 加速老化-accelerate

9、d ageing 塑性變形-plastic deformation 塑性流動-plastic fiow 翹曲-warp(ing),warpage 抗臭氧性-ozone resistance 抗臭氧試驗-ozone resistance test 耐天侯性-weatherability,weather resistance 耐光性-light resistance,light fastness 天侯老化試驗-weathering test 耐酸性-acid resistance 耐衝擊性-impact resistance 褪色-fading,discoloration 耐蝕性-corrosio

10、n resistance 拉桿,導柱-tie-bar 拉桿間距-tie-bar distance 多模穴模具-multi-cavity mold 雙色射出成形-double-shot molding 超音(聲)波鑲嵌-ultrasonic inserting 超音(聲)波焊接-ultrasonic welding 頂出,脫模-ejection 頂出組合-ejector 頂出板-ejector plate,knock-out plate 頂出桿,脫模桿-knock-out bar,ejector rod 無光面-dull surface 低壓射出成形法-low pressure injectio

11、n molding 硬度計-durometer 電鍍-electroplating,electrodeposition 電鑄模具-electroformed mold 尼龍,(聚醯胺樹脂之俗稱)-nylon 尼龍纖維-nylon fiber 扭曲試驗-torsion test 扭力矩-torsion moment 噴嘴,注嘴-nozzle 噴嘴接觸-nozzle touching 噴嘴止流-nozzle shut-off 支管形噴嘴-nozzle manifold 脫模銷,頂出銷-knock-out pin 脫模銷托板,頂出銷托板-knock-out pin plate 背壓-back pre

12、ssure 止回閥,止逆閥-back pressure valve 發泡劑-blowing agent,expanding agent 發泡塑膠,泡沫塑料-plastics foam,expanded plastics, foamed plastics,cellular plastics,plastics sponge 拋光布輪-buff,buffing wheel 布輪拋光-buffing 毛邊,整紋,溢料-flash,fin 修邊,除邊-deflashing,definning 修邊機,修毛邊機-deflasher 手工脫模,手工頂出-hand ejection 剝離,剝皮加工-peeli

13、ng 剝離試驗-peeling test 拉出成形-pultrusion 凹痕,縮痕-sink mark,shrink mark 抗刮硬度,刮痕硬度-scratch hardness 非破壞性試驗-non-destructive testing 起泡,氣泡-blister 疲勞試驗-fatigue test 疲勞壽命-fatigue life 疲勞強度-fatigue strength 針眼,針孔-pinhole 玻璃纖維強化,熱塑塑膠射出成形-fiberfil molding 起泡,氣泡-blister 底漆,底膠,引發劑-primer 溢料-flash 溢料縫,毛邊槽-flash groo

14、ve 流痕-flow mark 冷卻線-frost line 原型模,試驗模-prototype mold 環境溫度-ambient temperature 止流閥-shut-off valve 孔隙,空洞,氣泡-void 放電-discharge 全壓式模具-positive mold 輔助壓缸-auxiliary cylinder 燙印-hot stamping,roll leaf stamping 彎曲龜裂-flex cracking 磨損-abrasion,wear 磨耗-abrasion loss 莫斯硬度-Mohshardness 退火-annealing 回火-tempering

15、 楊氏彈性係數-Youngs modulus of elasticity 油壓增壓器-hydraulic intensifier 油壓機-hydraulic press 油壓馬達-hydraulic motor 焊接-welding 內襯,襯套,襯墊-liner 流道,流道料-runner 合模銷,導銷-leader pin 合模銷套,導銷襯套-leader pin bushing 回程銷, 覆歸銷-return pin 冷卻水通路-cooling channel 常溫成形,冷模壓-cold molding 老化試驗-ageing test 對位圈,定位環-locating ring 熔合線,

16、結合線-weld line 肉厚-wall thickness 脫模斜度-draft angle 母模-cavity side 頂出銷,頂針-ejector pin 分模線-parting line 澆口,灌點-gate 豎澆道-sprue 澆道,流道-runner 模仁,雄模,模心-core side 澆口白暈-gate bush 凹痕,縮痕,縮水-sink mark 銀線-silver line 隧道形澆口-tunnel gate 沉陷式澆口,潛入式澆口-submarine gate 針孔形澆口-pin point gate 注道形澆口,直接澆口-sprue gate 毛邊形澆口,薄膜形澆口-flash gate,external ring gate,internal ring gate 噴流,噴射現象-jetting 剝料板-stripper plate