Cisco Packet Tracer中设备模块用途.docx

《Cisco Packet Tracer中设备模块用途.docx》由会员分享，可在线阅读，更多相关《Cisco Packet Tracer中设备模块用途.docx（23页珍藏版）》请在三一办公上搜索。

1、Cisco Packet Tracer中设备模块用途Cisco Packet Tracer中设备模块用途HWIC-2T：The HWIC-2T is a Cisco 2-Port Serial High-Speed WAN Interface Card, providing 2 serial ports.HWIC-4ESW：The HWIC-4ESW provides four switching ports.HWIC-4ESW： 提供4个交换功能接口。HWIC-8A：The HWIC-8A provides up to eight asynchronous EIA-232 connectio

2、ns to console ports.WIC cover：The WIC cover plate provides protection for the internal electronic components. It also helps maintain adequate cooling by normalizing airflow.WIC盖板：可以保护内部电子元件。同时有助于保持足够的冷却气流.HWIC-AP-AG-B：The HWIC-AP-AG-B module is a High-Speed WAN Interface Card providing integrated Ac

3、cess Point functionality in the Cisco 1800 (Modular), Cisco 2800, and Cisco 3800 Integrated Services Routers. It supports Single Band 802.11b/g or Dual Band 802.11a/b/g radios.WIC-1AM:The WIC-1AM card features dual RJ-11 connectors, which are used for basic telephone service connections. The WIC-1AM

4、 uses one port for connection to a standard telephone line, and the other port can be connected to a basic analog telephone for use when the modem is idle.WIC-1AM：WIC-1AM卡特性：提供2个RJ11连接器，以满足基本电话服务链接需要。WIC-1AM使用一个端口满足仅仅一个标准的电话线链接，其它端口可以连接普通模拟电话机，当Modem空显示，就可以使用普通的模拟电话机。WIC-1ENET:The WIC-1ENET is a sin

5、gle-port 10 Mbps Ethernet interface card, for use with 10BASE-T Ethernet LANs.WIC-1ENET：WIC-1ENET 是一个单端口10Mbps以太网接口,用于10BASE-T局域网。WIC-1T:The WIC-1T provides a single port serial connection to remote sites or legacy serial network devices such as Synchronous Data Link Control (SDLC) concentrators, al

6、arm systems, and packet over SONET (POS) devices.WIC-1T：WIC-1T 提供一个串口，可以连接到远端站点、legacy串口网络设备诸如SDLC、告警系统或者POS接口。WIC-2AM:The WIC-2AM card features dual RJ-11 connectors, which are used for basic telephone service connections. The WIC-2AM has two modem ports to allow multiple data communication connect

7、ions.WIC-2AM特性：2个RJ-11连接器，被使用于普通电话服务。WIC-2AM有两个Modem接口用于多路数据通信。WIC2T:The 2-port asynchronous/synchronous serial network module provides flexible multi-protocol support, with each port individually configurable in synchronous or asynchronous mode, offering mixed media dial support in a single chassis

8、. Applications for asynchronous/synchronous support include: low speed WAN aggregation (up to 128 Kbps), dial-up modem support, Async or Sync connections to management ports of other equipment, and transport of legacy protocols such as Bi-sync and SDLC.WIC2T：2口同异步串口网络模块提供了灵活多协议支持，每个端口可以独立被配置为同步或者异步工

9、作模式，并提供在单个级别的混合媒介的拨号支持。同异步应用包括：低速广域网汇聚(最高128kbps)，拨号modem支持，异步或者同步链接以管理其它设备，并且传输传统的协议诸如Bi-sync and SDLC。NM-1E：The NM-1E features a single Ethernet port that can connect a LAN backbone which can also support either six PRI connections to aggregate ISDN lines, or 24 synchronous/asynchronous ports.NM-1

10、E特性:提供一个以太网端口，该端口可以连接一个局域网核心。该模块还支持6路PRI链路连接到ISDN汇聚链路，或者24路同异步端口。NM-1E2W：The NM-1E2W provides a single Ethernet port with two WIC slots that can support a single Ethernet LAN, together with two serial/ISDN backhaul lines, and still allow multiple serial or ISDN in the same chassis.NM-1E2W：NM-1E2W提供单

11、端口的以太网接口并带有两个WIC插槽，该插槽可以支持单端以太网接口，也支持两个串口、ISDN接口。NM-1FE-FX：The NM-1FE-FX Module provides one Fast-Ethernet interface for use with fiber media. Ideal for a wide range of LAN applications, the Fast Ethernet network modules support many internetworking features and standards. Single port network module

12、s offer autosensing 10/100BaseTX or 100BaseFX Ethernet.NM-1FE-FX特性:本模块提供一个快速以太网接口，介质是光纤。适合于组建远距离局域网应用，快速以太网模块支持多种特性和标准。单端口的网络模块支持10/100BaseTX自适应，或者100BaseFX光纤以太网。NM-1FE-TX：The NM-1FE-TX Module provides one Fast-Ethernet interface for use with copper media. Ideal for a wide range of LAN applications,

13、 the Fast Ethernet network modules support many internetworking features and standards. Single port network modules offer autosensing 10/100BaseTX or 100BaseFX Ethernet. The TX (copper) version supports virtual LAN (VLAN) deployment.NM-1FE-TX特性:该模块提供一个支持铜介质的快速以太网接口。适合于组建远距离局域网应用，快速以太网模块支持多种特性和标准。单端口

14、的网络模块支持10/100BaseTX自适应，或者100BaseFX光纤以太网。TX(铜介质)的版本支持虚拟局域网扩展。NM-1FE2W：The NM-1FE2W Module provides one Fast-Ethernet interface for use with copper media, in addition to two Wan Interface Card expansion slots. Ideal for a wide range of LAN applications, the Fast Ethernet network modules support many i

15、nternetworking features and standards. Single port network modules offer autosensing 10/100BaseTX or 100BaseFX Ethernet. The TX (copper) version supports virtual LAN (VLAN) deployment.NM-1FE2W模块提供1个使用双绞线的快速以太网接口，除此外还有2个广域网接口卡扩展槽。是大范围局域网应用的理想选择，快速以太网模块支持多种网络互连功能和标准。单个端口的网络模块提供10/100BaseTX或者100BaseFX自

16、适应以太网络，TX版本的支持部署VLAN。The NM-2E2W provides two Ethernet ports with two WIC slots that can support two Ethernet LANs, together with two serial/ISDN backhaul lines, and still allow multiple serial or ISDN in the same chassis.NM-2E2W提供单端口的以太网接口并带有两个WIC插槽，该插槽可以支持单端以太网接口，也支持两个串口、ISDN接口。The NM-2FE2W Module

17、 provides two Fast-Ethernet interfaces for use with copper media, in addition to two Wan Interface Card expansion slots. Ideal for a wide range of LAN applications, the Fast Ethernet network modules support many internetworking features and standards.NM-2FE2W特性:本模块提供2个光纤介质的快速以太网接口，还提供2个广域网接口卡扩展插槽。适合

18、于组建远距离局域网应用，快速以太网模块支持多种多种特性和标准。The NM-2W Module provides two WAN Interface Card expansion slots. It can be used with a broad range of interface cards, supporting a diverse array of physical media and network protocols.NM-2W模块提供两个广域网扩展插槽，可以用于支持各种不同的接口卡，以支持各种不同的物理介质和网络协议。The 4-port asynchronous/synchr

19、onous serial network module provides flexible multi-protocol support, with each port individually configurable in synchronous or asynchronous mode, offering mixed-media dial support in a single chassis. Applications for Asynchronous/Synchronous support include: Low speed WAN aggregation (up to 128 K

20、bps), dial-up modem support, Async or Sync connections to management ports of other equipment, and transport of legacy protocols such as Bi-sync and SDLC.NM4A/S：4端口 同异步串口网络模块提供多协议支持，每一个端口可以独立被配置为同步模式或者异步模式，并提供在单个级别的混合媒介的拨号支持。同异步应用包括：低速广域网汇聚(最高128kbps)，拨号modem支持，异步或者同步链接以管理其它设备，并且传输传统的协议诸如Bi-sync and

21、 SDLC。The NM-4E features four Ethernet ports for multifunction solutions that require higher-density Ethernet than the mixed-media network modules.NM-4E特性:提供4个以太端口，该模块为高密度以太网而非混合介质网络模块的用户需求提供多功能解决方案。The 8-port asynchronous/synchronous serial network module provides flexible multi-protocol support, w

22、ith each port individually configurable in synchronous or asynchronous mode, offering mixed-media dial support in a single chassis. Applications for Asynchronous/Synchronous support include: Low speed WAN aggregation (up to 128 Kbps), dial-up modem support, Async or Sync connections to management po

23、rts of other equipment, and transport of legacy protocols such as Bi-sync and SDLC.NM8A/S：8端口 同异步串口网络模块提供多协议支持，每一个端口可以独立被配置为同步模式或者异步模式，并提供在单个级别的混合媒介的拨号支持。同异步应用包括：低速广域网汇聚(最高128kbps)，拨号modem支持，异步或者同步链接以管理其它设备，并且传输传统的协议诸如Bi-sync and SDLC。The NM-8AM Integrated V.92 analog modem network module provides c

24、ost-effective analog telephone service connectivity for lower-density remote-access service (RAS), dial-out and fax-out modem access, asynchronous dial-on-demand routing (DDR) plus dial backup, and remote router management. Both the 8-port and 16-port versions use RJ-11 jacks to connect the integrat

25、ed modems to basic analog telephone lines on the public switched telephone network (PSTN) or private telephony systems.NM-8AM：NM-8AM集成V.92模拟Modem网络模块，该模块为低密度远端接入服务(RAS)、拨号呼叫、传真呼叫接入、异步按需拨号路由(DDR)触发拨号备份以及远程路由器管理等提供cost-effective模拟电话服务链接。不管是8端口还是16端口版本使用RJ-11水晶头链接集成Modem到PSTN或者专有电话系统的电话线上。The NM cover

26、plate provides protection for the internal electronic components. It also helps maintain adequate cooling by normalizing airflow.NM盖板可以保护内部的电子元件.有助于保持足够的冷却气流.The WIC-1AM card features dual RJ-11 connectors, which are used for basic telephone service connections. The WIC-1AM uses one port for connect

27、ion to a standard telephone line, and the other port can be connected to a basic analog telephone for use when the modem is idle.WIC-1AM卡特性：提供2个RJ11连接器，以满足基本电话服务链接需要。WIC-1AM使用一个端口满足仅仅一个标准的电话线链接，其它端口可以连接普通模拟电话机，当Modem空显示，就可以使用普通的模拟电话机。The WIC-1T provides a single port serial connection to remote site

28、s or legacy serial network devices such as Synchronous Data Link Control (SDLC) concentrators, alarm systems, and packet over SONET (POS) devices.WIC-1T 提供一个串口，可以连接到远端站点、legacy串口网络设备诸如SDLC、告警系统或者POS接口。The WIC-2AM card features dual RJ-11 connectors, which are used for basic telephone service connect

29、ions. The WIC-2AM has two modem ports to allow multiple data communication connections.WIC-2AM特性：2个RJ-11连接器，被使用于普通电话服务。WIC-2AM有两个Modem接口用于多路数据通信。NM-ESW-161提供16个交换功能端口。The PT-ROUTER-NM-1AM card features dual RJ-11 connectors, which are used for basic telephone service connections. The WIC-1AM uses on

30、e port for connection to a standard telephone line, and the other port can be connected to a basic analog telephone for use when the modem is idle.PT-ROUTER-NM-1AM卡特性：提供2个RJ11连接器，以满足基本电话服务链接需要。WIC-1AM使用一个端口满足仅仅一个标准的电话线链接，其它端口可以连接普通模拟电话机，当Modem空显示，就可以使用普通的模拟电话机。The PT-ROUTER-NM-1CE features a single

31、Ethernet port that can connect a LAN backbone which can also support either six PRI connections to aggregate ISDN lines, or 24 synchronous/asynchronous ports.PT-ROUTER-NM-1CE特性:提供一个以太网端口，该端口可以连接一个局域网核心。该模块还支持6路PRI链路连接到ISDN汇聚链路，或者24路同异步端口。The PT-ROUTER-NM-1CFE Module provides one Fast-Ethernet interf

32、ace for use with copper media. Ideal for a wide range of LAN applications, the Fast Ethernet network modules support many internetworking features and standards. Single port network modules offer autosensing 10/100BaseTX or 100BaseFX Ethernet. The TX (copper) version supports virtual LAN (VLAN) depl

33、oyment.PT-ROUTER-NM-1CFE特性:该模块提供一个支持铜介质的快速以太网接口。适合于组建远距离局域网应用，快速以太网模块支持多种特性和标准。单端口的网络模块支持10/100BaseTX自适应，或者100BaseFX光纤以太网。TX(铜介质)的版本支持虚拟局域网扩展。The single-port Cisco Gigabit Ethernet Network Module (part number PT-ROUTER-NM-1CGE) provides Gigabit Ethernet copper connectivity for access routers. The mo

34、dule is supported by the Cisco 2691, Cisco 3660, Cisco 3725, and Cisco 3745 series routers. This network module has one gigabit interface converter (GBIC) slot to carry any standard copper or optical Cisco GBIC.PT-ROUTER-NM-1CGE：单端口思科千兆以太网模块(PT-ROUTER-NM-1CGE)提供千兆网线连接用于连接路由器。cisco2691、3660、3725和3745

35、系类路由器支持该模块。模块有一个GBIC插槽用于电口或者光口类型的GBIC卡使用。The PT-ROUTER-NM-1FFE Module provides one Fast-Ethernet interface for use with fiber media. Ideal for a wide range of LAN applications, the Fast Ethernet network modules support many internetworking features and standards. Single port network modules offer au

36、tosensing 10/100BaseTX or 100BaseFX Ethernet.PT-ROUTER-NM-1FFE特性:本模块提供一个快速以太网接口，介质是光纤。适合于组建远距离局域网应用，快速以太网模块支持多种特性和标准。单端口的网络模块支持10/100BaseTX自适应，或者100BaseFX光纤以太网。The single-port Cisco Gigabit Ethernet Network Module (part number PT-ROUTER-NM-1FGE) provides Gigabit Ethernet copper connectivity for acce

37、ss routers. The module is supported by the Cisco 2691, Cisco 3660, Cisco 3725, and Cisco 3745 series routers. This network module has one gigabit interface converter (GBIC) slot to carry any standard copper or optical Cisco GBIC.PT-ROUTER-NM-1FGE：单端口思科千兆以太网模块(PT-ROUTER-NM-1FGE)提供千兆网线连接用于连接路由器。cisco2

38、691、3660、3725和3745系类路由器支持该模块。模块有一个GBIC插槽用于电口或者光口类型的GBIC卡使用。The PT-ROUTER-NM-1S provides a single port serial connection to remote sites or legacy serial network devices such as Synchronous Data Link Control (SDLC) concentrators, alarm systems, and packet over SONET (POS) devices.PT-ROUTER-NM-1S 提供一个

39、串口，可以连接到远端站点、legacy串口网络设备诸如SDLC、告警系统或者POS接口。The 2-port asynchronous/synchronous serial network module provides flexible multi-protocol support, with each port individually configurable in synchronous or asynchronous mode, offering mixed media dial support in a single chassis. Applications for asynch

40、ronous/synchronous support include: low speed WAN aggregation (up to 128 Kbps), dial-up modem support, Async or Sync connections to management ports of other equipment, and transport of legacy protocols such as Bi-sync and SDLC.PT-ROUTER-NM-1SS：2口同异步串口网络模块提供了灵活多协议支持，每个端口可以独立被配置为同步或者异步工作模式，并提供在单个级别的混

41、合媒介的拨号支持。同异步应用包括：低速广域网汇聚(最高128kbps)，拨号modem支持，异步或者同步链接以管理其它设备，并且传输传统的协议诸如Bi-sync and SDLC。The PT-SWITCH-NM-1CE features a single Ethernet port that can connect a LAN backbone which can also support either six PRI connections to aggregate ISDN lines, or 24 synchronous/asynchronous ports.PT-SWITCH-NM-

42、1CE特性:提供一个以太网端口，该端口可以连接一个局域网核心。该模块还支持6路PRI链路连接到ISDN汇聚链路，或者24路同异步端口。The PT-SWITCH-NM-1CFE Module provides one Fast-Ethernet interface for use with copper media. Ideal for a wide range of LAN applications, the Fast Ethernet network modules support many internetworking features and standards. Single po

43、rt network modules offer autosensing 10/100BaseTX or 100BaseFX Ethernet. The TX (copper) version supports virtual LAN (VLAN) deployment.PT-SWITCH-NM-1CFE特性:该模块提供一个支持铜介质的快速以太网接口。适合于组建远距离局域网应用，快速以太网模块支持多种特性和标准。单端口的网络模块支持10/100BaseTX自适应，或者100BaseFX光纤以太网。TX(铜介质)的版本支持虚拟局域网扩展。The single-port Cisco Gigabit

44、 Ethernet Network Module (part number PT-SWITCH-NM-1CGE) provides Gigabit Ethernet copper connectivity for access routers. The module is supported by the Cisco 2691, Cisco 3660, Cisco 3725, and Cisco 3745 series routers. This network module has one gigabit interface converter (GBIC) slot to carry an

45、y standard copper or optical Cisco GBIC.PT-SWITCH-NM-1CGE：单端口思科千兆以太网模块(PT-SWITCH-NM-1CGE)提供千兆网线连接用于连接路由器。cisco2691、3660、3725和3745系类路由器支持该模块。模块有一个GBIC插槽用于电口或者光口类型的GBIC卡使用。The PT-SWITCH-NM-1FFE Module provides one Fast-Ethernet interface for use with fiber media. Ideal for a wide range of LAN applicat

46、ions, the Fast Ethernet network modules support many internetworking features and standards. Single port network modules offer autosensing 10/100BaseTX or 100BaseFX Ethernet.PT-SWITCH-NM-1FFE特性:本模块提供一个快速以太网接口，介质是光纤。适合于组建远距离局域网应用，快速以太网模块支持多种特性和标准。单端口的网络模块支持10/100BaseTX自适应，或者100BaseFX光纤以太网。The single-

47、port Cisco Gigabit Ethernet Network Module (part number PT-SWITCH-NM-1FGE) provides Gigabit Ethernet optical connectivity for access routers. The module is supported by the Cisco 2691, Cisco 3660, Cisco 3725, and Cisco 3745 series routers. This network module has one gigabit interface converter (GBI

48、C) slot to carry any standard copper or optical Cisco GBIC.PT-SWITCH-NM-1FGE：单端口思科千兆以太网模块(PT-SWITCH-NM-1FGE)提供千兆光纤连接用于连接路由器。cisco2691、3660、3725和3745系类路由器支持该模块。模块有一个GBIC插槽用于电口或者光口类型的GBIC卡使用。The PT-REPEATER-NM-1CE features a single Ethernet port that can connect a LAN backbone which can also support e

49、ither six PRI connections to aggregate ISDN lines, or 24 synchronous/asynchronous ports.PT-REPEATER-NM-1CE特性:提供一个以太网端口，该端口可以连接一个局域网核心。该模块还支持6路PRI链路连接到ISDN汇聚链路，或者24路同异步端口。The PT-REPEATER-NM-1CFE Module provides one Fast-Ethernet interface for use with copper media. Ideal for a wide range of LAN applications, the Fast Ethernet network modules support many internetworking features and standards. Single port network modul