机械类外文文献翻译.doc

《机械类外文文献翻译.doc》由会员分享，可在线阅读，更多相关《机械类外文文献翻译.doc（13页珍藏版）》请在三一办公上搜索。

1、文献翻译英文原文：NOVEL METHOD OF REALIZING THE OPTIMAL TRANSMISSIONOF THE CRANK-AND-ROCKER MECHANISM DESIGNAbstract: A novel method of realizing the optimal transmission of the crank-and-rocker mechanism is presented. The optimal combination design is made by finding the related optimal transmission paramet

2、ers. The diagram of the optimal transmission is drawn. In the diagram, the relation among minimum transmission angle, the coefficient of travel speed variation, the oscillating angle of the rocker and the length of the bars is shown, concisely, conveniently and directly. The method possesses the mai

3、n characteristic. That it is to achieve the optimal transmission parameters under the transmission angle by directly choosing in the diagram, according to the given requirements. The characteristics of the mechanical transmission can be improved to gain the optimal transmission effect by the method.

4、 Especially, the method is simple and convenient in practical use.Keywords：Crank-and-rocker mechanism, Optimal transmission angle, Coefficient of travel speed variationINTRODUCTIONBy conventional method of the crank-and-rocker design, it is very difficult to realize the optimal combination between t

5、he various parameters for optimal transmission. The figure-table design method introduced in this paper can help achieve this goal. With given conditions, we can, by only consulting the designing figures and tables, get the relations between every parameter and another of the designed crank-and-rock

6、er mechanism. Thus the optimal transmission can be realized.The concerned designing theory and method, as well as the real cases of its application will be introduced later respectively.1 ESTABLISHMENT OF DIAGRAM FOR OPTIMAL TRANSMISSION DESIGN It is always one of the most important indexes that des

7、igners pursue to improve the efficiency and property of the transmission. The crank-and-rocker mechanism is widely used in the mechanical transmission. How to improve work ability and reduce unnecessary power losses is directly related to the coefficient of travel speed variation, the oscillating an

8、gle of the rocker and the ratio of the crank and rocker. The reasonable combination of these parameters takes an important effect on the efficiency and property of the mechanism, which mainly indicates in the evaluation of the minimum transmission angle. The aim realizing the optimal transmission of

9、 the mechanism is how to find the maximum of the minimum transmission angle. The design parameters are reasonably combined by the method of lessening constraints gradually and optimizing separately. Consequently, the complete constraint field realizing the optimal transmission is established.The fol

10、lowing steps are taken in the usual design method. Firstly, the initial values of the length of rocker and the oscillating angle of rocker are given. Then the value of the coefficient of travel speed variation is chosen in the permitted range. Meanwhile, the coordinate of the fixed hinge of crank po

11、ssibly realized is calculated corresponding to value .1.1 Length of bars of crank and rocker mechanismAs shown in Fig.1, left arc is the permitted field of point . The coordinates of point are chosen by small step from point to point .The coordinates of point are (1) (2)where , the step, is increase

12、d by small increment within range(0,). If the smaller the chosen step is, the higher the computational precision will be. is the radius of the design circle. is the distance from to . (3)Calculating the length of arc and , the length of the bars of the mechanism corresponding to point is obtained1,2

13、.1.2 Minimum transmission angle Minimum transmission angle (see Fig.2) is determined by the equations3 (4) (5) (6)where Length of crank(mm) Length of connecting bar(mm)Length of rocker(mm)Length of machine frame(mm)Firstly, we choose minimum comparing with . And then we record all values of greater

14、than or equal to and choose the maximum of them.Secondly, we find the maximum of corresponding to any oscillating angle which is chosen by small step in the permitted range (maximum of is different oscillating angle and the coefficient of travel speed variation ).Finally, we change the length of roc

15、ker by small step similarly. Thus we may obtain the maximum of corresponding to the different length of bars, different oscillating angle and the coefficient of travel speed variation .Fig.3 is accomplished from Table for the purpose of diagram design.It is worth pointing out that whatever the lengt

16、h of rocker is evaluated, the location that the maximum of arises is only related to the ratio of the length of rocker and the length of machine frame /, while independent of .2 DESIGN METHOD2.1 Realizing the optimal transmission design given the coefficient of travel speed variation and the maximum

17、 oscillating angle of the rockerThe design procedure is as follows.(1) According to given and , taken account to the formula the extreme included angle is found. The corresponding ratio of the length of bars / is obtained consulting Fig.3. (7)(2) Choose the length of rocker according to the work req

18、uirement, the length of the machine frame is obtained from the ratio /.(3) Choose the centre of fixed hinge as the vertex arbitrarily, and plot an isosceles triangle, the side of which is equal to the length of rocker (see Fig.4), and . Then plot , draw , and make angle . Thus the point of intersect

19、ion of and is gained. Finally, draw the circumcircle of triangle .(4) Plot an arc with point as the centre of the circle, as the radius. The arc intersections arc at point . Point is just the centre of the fixed hinge of the crank.Therefore, from the length of the crank (8)and the length of the conn

20、ecting bar (9)we will obtain the crank and rocker mechanism consisted of , , , and .Thus the optimal transmission property is realized under given conditions.2.2 Realizing the optimal transmission design given the length of the rocker (or the length of the machine frame) and the coefficient of trave

21、l speed variationWe take the following steps.(1) The appropriate ratio of the bars / can be chosen according to given . Furthermore, we find the length of machine frame (the length of rocker ).(2) The corresponding oscillating angle of the rocker can be obtained consulting Fig.3. And we calculate th

22、e extreme included angle .Then repeat (3) and (4) in section 2.13 DESIGN EXAMPLEThe known conditions are that the coefficient of travel speed variation and maximum oscillating angle . The crankandrocker mechanism realizing the optimal transmission is designed by the diagram solution method presented

23、 above.First, with Eq.(7), we can calculate the extreme included angle . Then, we find consulting Fig.3 according to the values of and .If evaluate mm, then we will obtain mm.Next, draw sketch(omitted).As result, the length of bars is mm, mm, mm, mm.The minimum transmission angle is The results obta

24、ined by computer are mm, mm, mm, mm.Provided that the figure design is carried under the condition of the Auto CAD circumstances, very precise design results can be achieved.4 CONCLUSIONS A novel approach of diagram solution can realize the optimal transmission of the crank-and-rocker mechanism. The

25、 method is simple and convenient in the practical use. In conventional design of mechanism, taking 0.1 mm as the value of effective the precision of the component sizes will be enough.译文：认识曲柄摇臂机构设计的最优传动方法摘要：一种曲柄摇臂机构设计的最优传动的方法被提出。这种优化组合设计被用来找出最优的传递参数。得出最优传递图。在图中，在极小的传动角度之间, 滑移速度变化系数，摇臂的摆动角度和杆的长度被直观地显

26、示。 这是这种方法拥有的主要特征。根据指定的要求，它将传动角度之下的最优传动参数直接地表达在图上。通过这种方法，机械传动的特性能用以获取最优传动效果。特别是， 这种方法是简单和实用的。关键字：曲柄摇臂机构 最优传动角度 滑移速度变化系数0 介绍由曲柄摇臂机构设计的常规方法, 在各种各样的参量之间很难找出优化组合的最优传动。通过本文介绍的图面设计方法可以帮助达到这个目的。在指定的情况下，通过观查设计图面, 我们就能得到每个参量和另外一个曲柄摇臂机构设计之间的联系。由因认识最优传动。具体的设计的理论和方法， 以及它们各自的应用事例将在以下介绍。1 优化传动设计的建立 优化传动的设计一直是设计师改进

27、传输效率和追求产量的最重要的索引的当中一个。曲柄摇臂机构被广泛应用在机械传动中。如何改进工作效率和减少多余的功率损失直接地与滑移速度变化系数，摇臂的摆动角度和曲柄摇臂的比率有关系。这些参数的合理组合采用对机械效率和产量有重要作用, 这些主要体现在极小的传输角度上。认识机械优化传动目的是找到极小的传输角度的最大值。设计参数是适度地减少限制而且分开的合理优化方法的结合。因此，完全限制领域的优化传动建立了。以下步骤被采用在通常的设计方法。 首先，测量出摇臂的长度和摇臂的摆动角度的初始值。 然后滑移速度变化系数的值被定在允许的范围内。 同时，曲柄固定的铰接座标可能被认为是任意值。1.1 曲柄摇臂机构杆

28、的长度由图Fig.1，左弧是点被允许的领域。点的座标的选择从点到点。点的座标是 (1) (2)当，高度，在range(0 ，) 被逐渐增加。如果选的越小,计算精度将越高。 是设计圆的半径。是从到的距离。 (3)计算弧和的长度，机械杆对应于点的长度是obtained1,2 。1.2 极小的传动角度 极小的传动角度 (参见Fig.2) 由equations3确定 (4) (5) (6)由于曲柄的长度(毫米) 连杆的长度（毫米） 摇臂的长度（毫米） 机器的长度（毫米）首先, 我们比较极小值和。 并且我们记录所有的值大于或等于，然后选择他们之间的最大值。第二, 我们发现最大值对应于一个逐渐变小的范围的

29、任一个摆动的角度 (最大值是不同于摆动的角度和滑移速度变化系数) 。最后, 我们相似地慢慢缩小摇臂的长度。 因而我们能获得最大值对应于杆的不同长度, 另外摆动的角度和滑移速度变化系数。Fig.3成功的表达设计的目的。它确定了无论是摇臂的长度,最大值出现的地点，只与摇臂的长度和机械的长度的比率/有关, 当确定时。2 设计方法2.1 认识最优传动设计下滑移速度变化系数和摇臂的最大摆动的角度设计步骤如下。(1) 根据所给的和， 通常采取对发现极限角度的解释。 杆的长度的对应的比率/是从图Fig.3获得的 。 (7)(2) 根据工作要求选择摇臂的长度， 机械的长度是从比率/获得的。(3) 任意地选择固

30、定的铰接的中心作为端点，并且做一个等腰三角形,令一条边与摇臂的长度相等 (参见Fig.4)，令。 然后做， 连接，并且做角度。 因而增加了交点和。 最后， 画三角形。(4)以点作为圆的中心，为半径画圆弧。 弧交点在点。 点是曲柄的固定铰接的中心。所以, 从曲柄的长度 (8)并且连杆的长度 (9)我们将获得曲柄摇臂机构包括，和。因而优化传动加工会在指定的情况下进行。2.2 认识优化传动设计下摇臂的长度(或机械的长度) 和滑移速度变化系数我们采取以下步骤。(1)根据选择的确定杆的适当比率/。 此外，我们得出机械 (摇臂的长度) 。(2) 摇臂对应的摆动的角度可以从图Fig.3 获得。 并且我们计算

31、出极限角度。然后根据2.1重覆(3) 和(4)3 设计例子已知的条件是, 滑移速度变化系数和最大摆动角度。 提出曲柄摇臂机械优化传动图方法设计方案。首先， 通过公式(7)，我们能计算出极限角度。 然后，我们通过表格Fig.3 查出以及和的值。假设mm, 然后我们将得出mm。然后, 做sketch(omitted) 。最后, 算出杆的长度分别是 mm, mm, mm, mm.极小传动角度是 结果由计算可得 mm， mm， mm， mm。在运用Auto CAD 制图设计的情况, 可达到非常精确设计结果。4结论认识图解法解答曲柄摇臂机构的最优传动。这种方法是简单和实用的。通常在机械设计中, 将0.1 毫米作为最小有效精度是足够的。