移动互联网产业园项目临时用电施工方案培训资料.docx

《移动互联网产业园项目临时用电施工方案培训资料.docx》由会员分享，可在线阅读，更多相关《移动互联网产业园项目临时用电施工方案培训资料.docx（42页珍藏版）》请在三一办公上搜索。

1、星火智谷移动互联网产业园项目星火智谷移动互联网产业园项目临时用电施工方案 编制人： 审核人： 审批人： 编制单位：江苏南通三建集团股份有限公司 编制日期： 年 月 日目录第一章、编制依据及工程概况11.编制依据12.工程简介13.工程概况1第二章、配电系统及计算书21.配电系统22.临时用电计算书3第三章、临时用电安全措施221.组织机构222.防雷与接地装置设计及用电安全技术措施223.电气火灾预防及扑灭措施26第四章、现场平面布置图、配电系统图271.现场平面布置图272.配电系统图282 第一章、编制依据及工程概况1.编制依据1.1建设单位及设计提供的施工图纸以及其它相关资料；1.2 现

2、行国家及地方施工技术规范、规程；1.3施工现场临时用电安全技术规范JGJ46-20051.4低压配电设计规范GB50054-20111.5建筑工程施工现场供电安全规范GB50194-20141.6工业与民用配电设计手册第三版1.7建筑施工安全检查标准JGJ59-20111.8广联达施工安全设施计算软件；2.工程简介工程名称：星火智谷移动互联网产业园二期工程建设单位：南京互信互通科技有限公司设计单位：南京城镇建筑设计咨询有限公司监理单位：南京腾江工程建设监理有限责任公司施工单位：江苏南通三建集团有限公司工程地址：南京市浦口区星火路东侧，东南大学成贤学院西侧，地铁3号线星火路站以南、东大路以北。3

3、. 工程概况3.1本项目由地下汽车车库、局部地下自行车停车库，上部C1#C4#、C5#楼共计5幢楼组成。主体C1#C4#为框架结构，C1C4#6层，结构总高度23.35米；主体C5#为框剪结构，C5#15层，结构总高度59.85米；地下室两层，其中地下一层层高4.7-6.5米，地下二层层高3.7米，地下室顶板覆土高度0.81.0米。3.2建筑结构设计使用年限为50年；地下室防水等级二级，种植顶板防水等级一级，变电所、配电房防水等级一级，抗震设防烈度七度，防护等级二等人员掩蔽工程，防核武器等级为六级；C1C4#楼为多层办公楼，结构安全等级二级，地上耐火等级二级，地下耐火等级一级，抗震设防烈度七度

4、；C5#楼为一类高层办公楼，结构安全等级二级，地上耐火等级一级，地下耐火等级一级，抗震设防烈度七度。第2章 、配电系统及计算书1. 配电系统1.1本工程用电主要负荷为施工现场照明、机械设备及钢筋、木工加工车间，办公室及生活区用电。1.2现场用电均从由建设单位提供的低压配电房109-3柜引出（断路器容量800A，电流互感器变比800：5）；一级配电房设置在二期C5东北角，内设两台配电柜（一台用于生活区供电，一台用于施工区域供电）导线截面和电箱选用见施工用电系统图。1.3采用三相五线制，所有室外固定的用电设备及电箱设专门接地装置。1.4室外电缆延墙、路边采用埋地敷设，过施工便道处穿过预留槽口；多股

5、五芯电缆分别接进临时办公楼、宿舍、和食堂或施工总电箱；现场用电线路均采用电缆沿外围墙及基坑四周暗敷设，楼层用电线路采用托吊方式。进入室内装修施工阶段，将楼层用电回路的线缆引入楼内，每3层设一台二级配电箱，并且首、顶层必须设楼层用电箱，便于楼内施工用电。1.5在变压器控制开关上引出电源，通过总配电箱后用主干线电缆送出。总箱配出线采用放射式和树干式相结合的配电方式三级配电示意图如下：开关箱分配电箱总配电箱2. 临时用电计算书2.1参数设置1、总箱参数用电接驳方式由变压器接入总配电箱编号总箱 A总配电箱距接驳点布线距离Lo(m)5总配电箱的同期使用系数Kx0.8分配电箱数量2导线线芯材料铜线总配电箱

6、进线敷设方式空气明敷/架空线路分配电箱进线敷设方式空气明敷/架空线路设备电线敷设方式空气明敷/架空线路干线允许电压降%52、分箱参数3、用电设备4、临电设备计算2.2初步设计(1)施工现场临时用电安全技术规范（JGJ46-2005）总则中以强制性条文规定，施工现场必须采用三级配电系统、必须采用TN-S接零保护系统。(2)现场采用380V低压供电，设一配电总箱，采用TN-S系统供电。(3)布置位置及线路走向参见临时配电系统图，采用三级配电，三级防护。(4)按照JGJ46-2005规定制定方案，接地电阻R4。(5)按照JGJ46-2005规定若为架空线路则“根据机械强度要求，绝缘铜线截面不小于10

7、mm2，绝缘铝线截面不小于16mm2”。2.3用电负荷1、1号分箱设备用电负荷(1)塔式起重机Kx = 0.7，Cos = 0.65，tg = (1 - Cos2)0.5/ Cos = (1 - 0.652)0.5 / 0.65 = 1.17Pe = n P (e/)0.5 = 2.00 32.80 (0.40 / 0.25)0.5 = 82.98kWIj1 = Kx Pe / (1.732 Ue cos) = 0.70 82.98 1000 / (1.732 380 0.65) = 135.77APjs = Kx Pe = 0.70 82.98 = 58.08kWQjs = Pjs tg =

8、 58.08 1.17 = 67.91kvA(2)施工升降机Kx = 0.3，Cos = 0.6，tg = (1 - Cos2)0.5/ Cos = (1 - 0.62)0.5 / 0.6 = 1.33Pe = n P (e/)0.5 = 2.00 22.00 (0.40 / 0.40)0.5 = 44.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.30 44.00 1000 / (1.732 380 0.60) = 33.43APjs = Kx Pe = 0.30 44.00 = 13.20kWQjs = Pjs tg = 13.20 1.33 = 17.60kv

9、A(3)自落式混凝土搅拌机Kx = 0.75，Cos = 0.85，tg = (1 - Cos2)0.5/ Cos = (1 - 0.852)0.5 / 0.85 = 0.62Pe = n P (e/)0.5 = 1.00 7.50 (0.40 / 0.40)0.5 = 7.50kWIj1 = Kx Pe / (1.732 Ue cos) = 0.75 7.50 1000 / (1.732 380 0.85) = 10.05APjs = Kx Pe = 0.75 7.50 = 5.62kWQjs = Pjs tg = 5.62 0.62 = 3.49kvA(4)插入式振动器Kx = 0.3，C

10、os = 0.7，tg = (1 - Cos2)0.5/ Cos = (1 - 0.72)0.5 / 0.7 = 1.02Pe = n P (e/)0.5 = 2.00 0.80 (0.40 / 0.40)0.5 = 1.60kWIj1 = Kx Pe / (1.732 Ue cos) = 0.30 1.60 1000 / (1.732 380 0.70) = 1.04APjs = Kx Pe = 0.30 1.60 = 0.48kWQjs = Pjs tg = 0.48 1.02 = 0.49kvA(5)钢筋调直机Kx = 0.65，Cos = 0.7，tg = (1 - Cos2)0.5/

11、 Cos = (1 - 0.72)0.5 / 0.7 = 1.02Pe = n P (e/)0.5 = 1.00 4.00 (0.40 / 0.40)0.5 = 4.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.65 4.00 1000 / (1.732 380 0.70) = 5.64APjs = Kx Pe = 0.65 4.00 = 2.60kWQjs = Pjs tg = 2.60 1.02 = 2.65kvA(6)钢筋切断机Kx = 0.65，Cos = 0.7，tg = (1 - Cos2)0.5/ Cos = (1 - 0.72)0.5 / 0.7 =

12、 1.02Pe = n P (e/)0.5 = 1.00 3.00 (0.40 / 0.40)0.5 = 3.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.65 3.00 1000 / (1.732 380 0.70) = 4.23APjs = Kx Pe = 0.65 3.00 = 1.95kWQjs = Pjs tg = 1.95 1.02 = 1.99kvA(7)钢筋弯曲机Kx = 0.65，Cos = 0.7，tg = (1 - Cos2)0.5/ Cos = (1 - 0.72)0.5 / 0.7 = 1.02Pe = n P (e/)0.5 = 1.00

13、 3.00 (0.40 / 0.40)0.5 = 3.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.65 3.00 1000 / (1.732 380 0.70) = 4.23APjs = Kx Pe = 0.65 3.00 = 1.95kWQjs = Pjs tg = 1.95 1.02 = 1.99kvA(8)交流电焊机Kx = 0.5，Cos = 0.4，tg = (1 - Cos2)0.5/ Cos = (1 - 0.42)0.5 / 0.4 = 2.29Pe = n P (e/)0.5 = 1.00 9.00 (0.50 / 1.00)0.5 = 6.36

14、kWIj1 = Kx Pe / (1.732 Ue cos) = 0.50 6.36 1000 / (1.732 380 0.40) = 12.09APjs = Kx Pe = 0.50 6.36 = 3.18kWQjs = Pjs tg = 3.18 2.29 = 7.29kvA(9)电动抹光机Kx = 0.1，Cos = 0.45，tg = (1 - Cos2)0.5/ Cos = (1 - 0.452)0.5 / 0.45 = 1.98Pe = n P (e/)0.5 = 1.00 1.50 (0.40 / 0.40)0.5 = 1.50kWIj1 = Kx Pe / (1.732 Ue

15、 cos) = 0.10 1.50 1000 / (1.732 380 0.45) = 0.51APjs = Kx Pe = 0.10 1.50 = 0.15kWQjs = Pjs tg = 0.15 1.98 = 0.30kvA(10)木工圆锯Kx = 0.65，Cos = 0.6，tg = (1 - Cos2)0.5/ Cos = (1 - 0.62)0.5 / 0.6 = 1.33Pe = n P (e/)0.5 = 2.00 3.00 (0.40 / 0.40)0.5 = 6.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.65 6.00 1000 / (1.

16、732 380 0.60) = 9.88APjs = Kx Pe = 0.65 6.00 = 3.90kWQjs = Pjs tg = 3.90 1.33 = 5.20kvA(11)真空吸水泵Kx = 0.75，Cos = 0.8，tg = (1 - Cos2)0.5/ Cos = (1 - 0.82)0.5 / 0.8 = 0.75Pe = n P (e/)0.5 = 2.00 4.00 (0.40 / 0.40)0.5 = 8.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.75 8.00 1000 / (1.732 380 0.80) = 11.40APjs =

17、 Kx Pe = 0.75 8.00 = 6.00kWQjs = Pjs tg = 6.00 0.75 = 4.50kvA(12)高压钠灯Kx = 0.6，Cos = 0.7，tg = (1 - Cos2)0.5/ Cos = (1 - 0.72)0.5 / 0.7 = 1.02Pe = n P (e/)0.5 = 2.00 1.00 (0.40 / 0.40)0.5 = 2.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.60 2.00 1000 / (1.732 380 0.70) = 2.60APjs = Kx Pe = 0.60 2.00 = 1.20kWQj

18、s = Pjs tg = 1.20 1.02 = 1.22kvA(13)碘钨灯Kx = 0.6，Cos = 0.6，tg = (1 - Cos2)0.5/ Cos = (1 - 0.62)0.5 / 0.6 = 1.33Pe = n P (e/)0.5 = 10.00 0.50 (0.40 / 0.40)0.5 = 5.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.60 5.00 1000 / (1.732 380 0.60) = 7.60APjs = Kx Pe = 0.60 5.00 = 3.00kWQjs = Pjs tg = 3.00 1.33 = 4.00

19、kvA(14)套丝切管机Kx = 0.2，Cos = 0.65，tg = (1 - Cos2)0.5/ Cos = (1 - 0.652)0.5 / 0.65 = 1.17Pe = n P (e/)0.5 = 1.00 1.00 (0.40 / 0.40)0.5 = 1.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.20 1.00 1000 / (1.732 380 0.65) = 0.47APjs = Kx Pe = 0.20 1.00 = 0.20kWQjs = Pjs tg = 0.20 1.17 = 0.23kvA(15)1号分箱计算负荷用电设备同期使用系数

20、Kx=0.80；Ijs = Kx Pe / (1.732 Ue Cos) = 0.80 175.94 1000 / (1.732 380 0.75) = 285.15A；同时要求分箱用电负荷不得小于分箱下用电设备最大计算负荷的1.1倍，故：Ijs = max285.15,1.1max(135.77,33.43,10.05,1.04,5.64,4.23,4.23,12.09,0.51,9.88,11.40,2.60,7.60,0.47,) = 285.15A2、2号分箱设备用电负荷(1)塔式起重机Kx = 0.7，Cos = 0.65，tg = (1 - Cos2)0.5/ Cos = (1 -

21、 0.652)0.5 / 0.65 = 1.17Pe = n P (e/)0.5 = 1.00 27.50 (0.40 / 0.25)0.5 = 34.79kWIj1 = Kx Pe / (1.732 Ue cos) = 0.70 34.79 1000 / (1.732 380 0.65) = 56.92APjs = Kx Pe = 0.70 34.79 = 24.35kWQjs = Pjs tg = 24.35 1.17 = 28.47kvA(2)载货电梯Kx = 0.3，Cos = 0.6，tg = (1 - Cos2)0.5/ Cos = (1 - 0.62)0.5 / 0.6 = 1.

22、33Pe = n P (e/)0.5 = 4.00 7.50 (0.40 / 0.40)0.5 = 30.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.30 30.00 1000 / (1.732 380 0.60) = 22.79APjs = Kx Pe = 0.30 30.00 = 9.00kWQjs = Pjs tg = 9.00 1.33 = 12.00kvA(3)自落式混凝土搅拌机Kx = 0.75，Cos = 0.85，tg = (1 - Cos2)0.5/ Cos = (1 - 0.852)0.5 / 0.85 = 0.62Pe = n P (e/)0

23、.5 = 2.00 5.50 (0.40 / 0.40)0.5 = 11.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.75 11.00 1000 / (1.732 380 0.85) = 14.75APjs = Kx Pe = 0.75 11.00 = 8.25kWQjs = Pjs tg = 8.25 0.62 = 5.11kvA(4)插入式振动器Kx = 0.3，Cos = 0.7，tg = (1 - Cos2)0.5/ Cos = (1 - 0.72)0.5 / 0.7 = 1.02Pe = n P (e/)0.5 = 2.00 0.80 (0.40 / 0

24、.40)0.5 = 1.60kWIj1 = Kx Pe / (1.732 Ue cos) = 0.30 1.60 1000 / (1.732 380 0.70) = 1.04APjs = Kx Pe = 0.30 1.60 = 0.48kWQjs = Pjs tg = 0.48 1.02 = 0.49kvA(5)钢筋调直机Kx = 0.65，Cos = 0.7，tg = (1 - Cos2)0.5/ Cos = (1 - 0.72)0.5 / 0.7 = 1.02Pe = n P (e/)0.5 = 1.00 4.00 (0.40 / 0.40)0.5 = 4.00kWIj1 = Kx Pe

25、/ (1.732 Ue cos) = 0.65 4.00 1000 / (1.732 380 0.70) = 5.64APjs = Kx Pe = 0.65 4.00 = 2.60kWQjs = Pjs tg = 2.60 1.02 = 2.65kvA(6)钢筋切断机Kx = 0.65，Cos = 0.7，tg = (1 - Cos2)0.5/ Cos = (1 - 0.72)0.5 / 0.7 = 1.02Pe = n P (e/)0.5 = 1.00 7.00 (0.40 / 0.40)0.5 = 7.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.65 7.00

26、 1000 / (1.732 380 0.70) = 9.88APjs = Kx Pe = 0.65 7.00 = 4.55kWQjs = Pjs tg = 4.55 1.02 = 4.64kvA(7)钢筋弯曲机Kx = 0.65，Cos = 0.7，tg = (1 - Cos2)0.5/ Cos = (1 - 0.72)0.5 / 0.7 = 1.02Pe = n P (e/)0.5 = 1.00 3.00 (0.40 / 0.40)0.5 = 3.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.65 3.00 1000 / (1.732 380 0.70) = 4

27、.23APjs = Kx Pe = 0.65 3.00 = 1.95kWQjs = Pjs tg = 1.95 1.02 = 1.99kvA(8)交流电焊机Kx = 0.5，Cos = 0.4，tg = (1 - Cos2)0.5/ Cos = (1 - 0.42)0.5 / 0.4 = 2.29Pe = n P (e/)0.5 = 1.00 9.00 (0.50 / 1.00)0.5 = 6.36kWIj1 = Kx Pe / (1.732 Ue cos) = 0.50 6.36 1000 / (1.732 380 0.40) = 12.09APjs = Kx Pe = 0.50 6.36

28、= 3.18kWQjs = Pjs tg = 3.18 2.29 = 7.29kvA(9)木工圆锯Kx = 0.65，Cos = 0.6，tg = (1 - Cos2)0.5/ Cos = (1 - 0.62)0.5 / 0.6 = 1.33Pe = n P (e/)0.5 = 2.00 3.00 (0.40 / 0.40)0.5 = 6.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.65 6.00 1000 / (1.732 380 0.60) = 9.88APjs = Kx Pe = 0.65 6.00 = 3.90kWQjs = Pjs tg = 3.90 1

29、.33 = 5.20kvA(10)真空吸水泵Kx = 0.75，Cos = 0.8，tg = (1 - Cos2)0.5/ Cos = (1 - 0.82)0.5 / 0.8 = 0.75Pe = n P (e/)0.5 = 2.00 4.00 (0.40 / 0.40)0.5 = 8.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.75 8.00 1000 / (1.732 380 0.80) = 11.40APjs = Kx Pe = 0.75 8.00 = 6.00kWQjs = Pjs tg = 6.00 0.75 = 4.50kvA(11)高压钠灯Kx =

30、0.6，Cos = 0.7，tg = (1 - Cos2)0.5/ Cos = (1 - 0.72)0.5 / 0.7 = 1.02Pe = n P (e/)0.5 = 1.00 1.00 (0.40 / 0.40)0.5 = 1.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.60 1.00 1000 / (1.732 380 0.70) = 1.30APjs = Kx Pe = 0.60 1.00 = 0.60kWQjs = Pjs tg = 0.60 1.02 = 0.61kvA(12)碘钨灯Kx = 0.6，Cos = 0.6，tg = (1 - Cos2)0

31、.5/ Cos = (1 - 0.62)0.5 / 0.6 = 1.33Pe = n P (e/)0.5 = 10.00 0.50 (0.40 / 0.40)0.5 = 5.00kWIj1 = Kx Pe / (1.732 Ue cos) = 0.60 5.00 1000 / (1.732 380 0.60) = 7.60APjs = Kx Pe = 0.60 5.00 = 3.00kWQjs = Pjs tg = 3.00 1.33 = 4.00kvA(13)2号分箱计算负荷用电设备同期使用系数Kx=0.80；Ijs = Kx Pe / (1.732 Ue Cos) = 0.80 117.7

32、5 1000 / (1.732 380 0.75) = 190.83A；同时要求分箱用电负荷不得小于分箱下用电设备最大计算负荷的1.1倍，故：Ijs = max190.83,1.1max(56.92,22.79,14.75,1.04,5.64,9.88,4.23,12.09,9.88,11.40,1.30,7.60,) = 190.83A3、总箱计算负荷总的计算负荷计算，总配电箱用电设备同期使用系数取Kx = 0.80总的有功功率： Pjs = KxPjs = 0.80 169.38 = 135.51kW总的无功功率： Qjs = KxQjs = 0.80 195.82 = 156.66kva

33、r总的视在功率： Sjs = (Pjs2 + Qjs2)0.5 = (135.51 135.51 + 156.66 156.66)0.5 = 207.13kVA总的计算电流计算：Ijs = Sjs 1000 /(1.732 Ue) = 207.13 1000 / (1.732 380) = 314.71A同时要求总箱下计算负荷不得小于分箱计算负荷的1.1倍，故：Ijs = max314.71,1.1max(285.15,190.83,) = 314.71A2.4导线及开关箱内电气设备选择1、1号干线上导线及开关箱内电气设备选择1.1、塔式起重机导线及开关箱内电气设备选择根据计算负荷，知塔式起重

34、机计算电流为：Ij1 = KxPe/(1.732Uecos) = 135.77A(1)选择YJV-0.6/1kV-325+216，安全载流量为136A135.77A。(2)选择开关箱内开关为HR3-400/150，其熔体额定电流为Ir = 150A 135.77A，漏电保护器为DZL25-200/160。1.2、施工升降机导线及开关箱内电气设备选择根据计算负荷，知施工升降机计算电流为：Ij2 = KxPe/(1.732Uecos) = 33.43A(1)选择VV22-310+16，安全载流量为64A33.43A。(2)选择开关箱内开关为HR6-160/35，其熔体额定电流为Ir = 35A 3

35、3.43A，漏电保护器为3KM1L-63/40。1.3、自落式混凝土搅拌机导线及开关箱内电气设备选择根据计算负荷，知自落式混凝土搅拌机计算电流为：Ij3 = KxPe/(1.732Uecos) = 10.05A(1)选择VV22-310+16，安全载流量为64A10.05A。(2)选择开关箱内开关为HH3-15/15，其熔体额定电流为Ir = 15A 10.05A，漏电保护器为DZ15LE-63/15。1.4、插入式振动器导线及开关箱内电气设备选择根据计算负荷，知插入式振动器计算电流为：Ij4 = KxPe/(1.732Uecos) = 1.04A(1)选择VV22-310+16，安全载流量为

36、64A1.04A。(2)选择开关箱内开关为HR5-100/4，其熔体额定电流为Ir = 4A 1.04A，漏电保护器为DZ15LE-40/6。1.5、钢筋调直机导线及开关箱内电气设备选择根据计算负荷，知钢筋调直机计算电流为：Ij5 = KxPe/(1.732Uecos) = 5.64A(1)选择VV22-310+16，安全载流量为64A5.64A。(2)选择开关箱内开关为HR6-160/6，其熔体额定电流为Ir = 6A 5.64A，漏电保护器为DZ15LE-40/6。1.6、钢筋切断机导线及开关箱内电气设备选择根据计算负荷，知钢筋切断机计算电流为：Ij6 = KxPe/(1.732Uecos

37、) = 4.23A(1)选择VV22-310+16，安全载流量为64A4.23A。(2)选择开关箱内开关为HR6-160/6，其熔体额定电流为Ir = 6A 4.23A，漏电保护器为DZ15LE-40/6。1.7、钢筋弯曲机导线及开关箱内电气设备选择根据计算负荷，知钢筋弯曲机计算电流为：Ij7 = KxPe/(1.732Uecos) = 4.23A(1)选择VV22-310+16，安全载流量为64A4.23A。(2)选择开关箱内开关为HR6-160/6，其熔体额定电流为Ir = 6A 4.23A，漏电保护器为DZ15LE-40/6。1.8、交流电焊机导线及开关箱内电气设备选择根据计算负荷，知交

38、流电焊机计算电流为：Ij8 = KxPe/(1.732Uecos) = 12.09A(1)选择VV22-310+16，安全载流量为64A12.09A。(2)选择开关箱内开关为HH3-15/15，其熔体额定电流为Ir = 15A 12.09A，漏电保护器为DZ15LE-63/15。1.9、电动抹光机导线及开关箱内电气设备选择根据计算负荷，知电动抹光机计算电流为：Ij9 = KxPe/(1.732Uecos) = 0.51A(1)选择VV22-310+16，安全载流量为64A0.51A。(2)选择开关箱内开关为HR5-100/4，其熔体额定电流为Ir = 4A 0.51A，漏电保护器为DZ15LE

39、-40/6。1.10、木工圆锯导线及开关箱内电气设备选择根据计算负荷，知木工圆锯计算电流为：Ij10 = KxPe/(1.732Uecos) = 9.88A(1)选择VV22-310+16，安全载流量为64A9.88A。(2)选择开关箱内开关为HR5-100/10，其熔体额定电流为Ir = 10A 9.88A，漏电保护器为DZ15LE-63/10。1.11、真空吸水泵导线及开关箱内电气设备选择根据计算负荷，知真空吸水泵计算电流为：Ij11 = KxPe/(1.732Uecos) = 11.40A(1)选择VV22-310+16，安全载流量为64A11.40A。(2)选择开关箱内开关为HH3-1

40、5/15，其熔体额定电流为Ir = 15A 11.40A，漏电保护器为DZ15LE-63/15。1.12、高压钠灯导线及开关箱内电气设备选择根据计算负荷，知高压钠灯计算电流为：Ij12 = KxPe/(1.732Uecos) = 2.60A(1)选择VV22-310+16，安全载流量为64A2.60A。(2)选择开关箱内开关为HR5-100/4，其熔体额定电流为Ir = 4A 2.60A，漏电保护器为DZ15LE-40/6。1.13、碘钨灯导线及开关箱内电气设备选择根据计算负荷，知碘钨灯计算电流为：Ij13 = KxPe/(1.732Uecos) = 7.60A(1)选择VV22-310+16

41、，安全载流量为64A7.60A。(2)选择开关箱内开关为HR5-100/10，其熔体额定电流为Ir = 10A 7.60A，漏电保护器为DZ15LE-63/10。1.14、套丝切管机导线及开关箱内电气设备选择根据计算负荷，知套丝切管机计算电流为：Ij14 = KxPe/(1.732Uecos) = 0.47A(1)选择VV22-310+16，安全载流量为64A0.47A。(2)选择开关箱内开关为HR5-100/4，其熔体额定电流为Ir = 4A 0.47A，漏电保护器为DZ15LE-40/6。1.15、分箱B1进线及开关箱内电气设备选择根据计算负荷，知1号分箱计算电流为：Ijs = 285.1

42、5A(1)选择电缆YJV-0.6/1kV-395+250，安全载流量为286A 285.15A，电缆截面面积为95mm2。按照允许电压降为5%，导线截面为：S1 = Kx1 Pe L1 /(C 5 )= 0.80 175.94 50.00 / (77.00 5.00) = 18.28mm2 95mm2(2) 选择开关箱内开关为HR5-400/300，其熔体额定电流为Ir = 300A 285.15A，漏电保护器为DZ20L-630/315。符合要求2、2号干线上导线及开关箱内电气设备选择2.1、塔式起重机导线及开关箱内电气设备选择根据计算负荷，知塔式起重机计算电流为：Ij1 = KxPe/(1.732Uecos) = 56.92A(1)选择VV22-310+16，安全载流量为64A56.92A。(2)选择开关箱内开关为HR3-100/60，其熔体额定电流为Ir = 60A 56.92A，漏电保护器为DZ4