E_PC200-8-Monitor_s--控制面板课件.ppt

《E_PC200-8-Monitor_s--控制面板课件.ppt》由会员分享，可在线阅读，更多相关《E_PC200-8-Monitor_s--控制面板课件.ppt（65页珍藏版）》请在三一办公上搜索。

1、,PC200-8,Monitor Operation,PC200-8,Contents,Page1. Outline of Screens and Switches 3,42.Function Switches53.Start-up Screen and End Screen64.Reading Service Meter after Powering Off 75.Work Mode Selection 8,96.Travel Speed Selection107.Auto-decelerator Selection, Wiper Switch/Washer Switch 11,128.Ai

2、r-Conditioner Display Screen 139.ECO Display/Energy-Saving Guidance Display 1410.Camera Screen 15,1611. Service Meter/Clock Selection 1712.Maintenance Screen1813.User Menu Screen19(1) Breaker/Attachment Setting 20 - 22(2) Screen Adjustment23(3) Clock Adjustment 24(4) Language Setting 25(5) Economy M

3、ode Adjustment2614.Cautions 28,Page15.Service Menu Screen 28 (1) Monitoring29(2) Failure History30 ,31(3) Maintenance History32(4) Maintenance Mode Change33(5) Telephone Number Setting34(6) Initial Setting 35 - 43(7) Adjustment44 - 47(8) Operation in Reduced Cylinder Mode 48,49(9) No-injection Crank

4、ing 50(10) Fuel Consumption Display 5116. Password Setting52,5317. Password Entry Screen at Power-ON5418. Attachment/Maintenance Password Setting5519. List of Cautions and Icons5620. Monitoring Code Table57 - 6121. List of User Codes 6222. Error Code Table63 65,ContentsPagePage,Outline of Screens an

5、d Switches (1),Work mode and wiper SW,Function SW,Air-conditioner SW,Outline of Screens and Switche,Outline of Screens and Switches (2),Outline of Screens and Switche,Function Switches,8-type multi-monitor adopts 6 functional switches.,Function Switches8-type multi-,Start-up Screen and End Screen,Po

6、wer-ON,Power-OFF,Komatsu logo screen (for 2 sec),Start-up inspection screen (2 sec),Work mode and travel display (2 sec),Normal screen,Screen display remains 5 sec.,Start-up Screen and End Screen,Service Meter Reading with Key-OFF,Keep Buzzer cancel SW and Auto-decelerator SW pressed,Service Meter R

7、eading with Key,Work Mode Selection (1),If no operation is made for 5 sec and over, press F5 (return) to return to the normal screen,Press Work Mode Select SW,selects a work mode from P E L B P,1),2),Press to confirm the selected mode,Displays 2 sec,Displays 2 sec,Each pressing of,Work mode can be s

8、elected also by using ( ) and ( ),Work Mode Selection (1)If no o,Work Mode Selection (2),If no operation is made for 5 sec and over, press F5 (return) to return to the normal screen,Press Work Mode Select SW,Press to select B,1),2),Press ( ) to select B,Press ( ) to confirm the selected mode,If brea

9、ker mode is selected, the screen to the left always appears.,Work Mode Selection (2)If no o,Travel Speed Selection,Each pressing of Travel Speed Select SW selects a speed from Lo Mi Hi,Displays 2 sec,Displays 2 sec,Travel Speed SelectionEach pre,Auto-Decelerator Selection,When auto-decel is selected

10、, an icon appears to the upper left-hand corner of the screen.,Pressing Auto-Decel Select Switch selects auto-deceleration.,Auto-Decelerator SelectionWhen,Wiper Switch/Washer Switch,Each pressing of Wiper Switch selects INT ON OFF .,Washer operates while Washer Switch is pressed.,An icon appears to

11、the upper left-hand corner of the screen while the wiper is in operation.The figure below indicates INT wiping operation,Wiper Switch/Washer SwitchEach,Air-Conditioner Display Screen,If no operation is made for 5 sec and over, press F5 (return) or F6 (decide) to return to the normal screen,:Automati

12、c air-conditioning switch,:Automatic air-conditioning switch,:Air-conditioner switch,:OFF switch,:Air flow rate setting (for 6-stage adjustment),:Inside/outside air selection,:Temperature setting,:Air blow selection,LCD,Air blow mode,Air outlet port,Remarks,Front blow out,Front and rear blow out,Fro

13、nt and rear below blow out,Defroster blow out,Blow out downward,Blow out downwardDefroster blow out,Air-Conditioner Display Screen,ECO Display/Energy-Saving Guidance Display,ECO display,This display indicates the work load state.If the indicator changes to orange, it does not mean machine failure,En

14、ergy-saving guidance display,If the lever remains in neutral position successively for 5 minutes and over without error/caution indication, the display changes to this screen, prompting operator to stop engine.A lever operation or pressing F5 restores the original screen.,ECO Display/Energy-Saving G

15、uid,Camera Screen,Press F3 switch ( ),Camera mark appears to F3 key only if camera setting is present,Press F5 switch ( ),Camera 1 and 2 screens appear,: Screen display for the first camera set up: Screen display for the second camera set up: Screen display for the 3rd camera set up: Camera 1 and 2

16、screens appear,Camera ScreenPress F3 switch (,Camera Screen (Warning, Error Generation and Other Operations),Error generation time,If an error is generated and the lever is at neutral position for 10 sec and over, the display returns to normal screen,If error & caution are generated,If air-condition

17、 operation, travel speed selection or work mode change is made on the camera screen, the display shifts to respective screen.,After the operation is completed, the display returns to the standard screen.,After the operation is completed, the display returns to the standard screen.,After the operatio

18、n is completed, the display returns to the camera screen.,Camera Screen (Warning, Error,Service Meter/Clock Selection,When displaying clock,When displaying service meter,Each pressing of F4 function switch selects the clock and service meter display alternately,Service Meter/Clock Selection,Maintena

19、nce Screen,Maintenance itemEngine oil replacementEngine oil filter replacementFuel main filter replacementFuel pre-filter replacementHydraulic oil filter replacementHydraulic oil tank breather replacementDamper case oil check and replenishmentFinal case oil replacementHydraulic oil replacement,Press

20、ing F5 ( ) function switch selects this screen,Maintenance time reset screen,Select an item and press F6 switch,To reset press F6 ( ),Pressing F5 or F6 switch or making no operation for 30 sec restores the normal screen,Maintenance ScreenMaintenance,User Menu Screen,Pressing F6 ( ) function switch s

21、elects this screen,Select and press F6 switch to shift to a selected screen.,User menu item Breaker/Attachment setting (displayed only when attachment setting is made) Message display (displayed only when KOMTRAX is present) Screen adjustment Clock adjustment Language setting Economy mode adjustment

22、,Press F5 switch to return to normal screen,User Menu ScreenPressing F6 (,Breaker/Attachment Setting,Select the breaker/attachment setting item and press F6 switch,Work mode select screen,B, ATT appear on the work mode select screen on the machine installed with the breaker and attachment,Breaker/At

23、tachment SettingSele,Breaker Mode Flow Rate Setting Change,Select breaker and press F6 switch,Work mode select screen,Default setting is as follows:Breaker 180 l/minBreaker 100 l/min,Breaker setting,Breaker flow rate setting change,Select the breaker flow rate item with F3 and confirm with F6,Breake

24、r flow rate setting screen,Select the breaker with F3 and F4 and confirm with F6,Select the flow rate with F3 and F4 and confirm with F6,Press F5 to return to the preceding screen,Breaker Mode Flow Rate Setting,Attachment Flow Rate Setting Change,Select attachment and press F6 switch,Default setting

25、 is as follows:Attachment 430 l/minAttachment 430 l/min,Attachment flow rate setting change,Select the attachment flow rate item with F3 and confirm with F6,Select the attachment with F3 and F4 and confirm with F6,Select the flow rate with F3 and F4 and confirm with F6,Attachment flow rate setting s

26、creen,(A),(B),Attachment setting,Attachment Flow Rate Setting C,Screen Adjustment,Daytime screen adjustment,Nighttime screen adjustment,Select the screen adjust item and press F6 switch,Light switch,For night,For daytime,F2: Resets all adjusted values to the default valuesF3: Shifts the indicator to

27、 the leftF4: Shifts the indicator to the rightF5: Returns to the user menu screenF6: Confirms the change and shifts on to the following itemShifts to luminance adjustment Contrast adjustment Brightness adjustment and back to luminance adjustment,Screen AdjustmentDaytime scree,Clock Adjustment,Select

28、 the clock adjust item and press F6 switch,F3: Advances time by one (1) hour(For minute adjustment, this advances time by one (1) minute),F4: Sets the time back by one (1) hour(For minute adjustment, this sets the time back by one (1) minute),:F3: Shifts to the item on the left:F4: Shifts to the ite

29、m on the right:F5: Cancels the change and returns to the user menu screen:F6: Confirms the change,Clock AdjustmentSelect the clo,Language Setting,Ten (10) languages indicated in the diagram below can be set up,F3: Moves down to an item directly belowF4: Moves up to an item directly aboveF5: Cancels

30、the change and returns to the user menu screenF6: Confirms the change and shifts on to the user menu screen,Select the language setting item and press F6 switch,Language SettingTen (10) langu,Economy Mode Adjustment,Eco-mode (E) is available for the fuel-economy-minded customers,Select the economy m

31、ode adjust item and press F6 switch,F3: Moves down to an item directly belowF4: Moves up to an item directly aboveF5: Cancels the change and returns to the user menu screenF6: Confirms the change and shifts on to the user menu screen,Economy Mode AdjustmentEco-mod,Cautions,項目,交換,交換,燃料交換,燃料交換,作動油交換,作

32、動油交換,点検補充,交換,交換,作動油交換,Hydraulic oil temperature drop,Automatic preheating indication,Charging voltage drop,Coolant capacity drop,Water in fuel,Hydraulic oil temperature rise,Overheat,Engine oil capacity drop,Fuel level low,Cautions項目,Service Menu Screen,Pressing +1,2,3 selects screens,Service menu i

33、tem01Monitoring02Failure history03Maintenance history04Maintenance mode change05Telephone number setting06Default setting07Adjustment08Arm crane setting09Operation on reduced cylinders10No-injection cranking11Fuel consumption display12KOMTRAX setting indication (only when KOMTRAX setting provided)13

34、KOMTRAX message indication (only when KOMTRAX setting provided),Select an item and press F6 switch to shift to a selected screen.,Service Menu ScreenPressing,Monitoring,Select the monitoring item and press F6 switch,Select the item and press F6 switchUp to 6 items can be selected. Enter 99999 and pr

35、ess F6 to select the monitoring screen.(The monitoring screen appears also by pressing F6 a bit longer or by double-clicking F6),Select an item and press F6 switch to shift to a selected screen.,Pressing Hold (F4) fixes the numeric value at the time of the pressing.,Pressing the work mode select, tr

36、avel select or auto-decel switch during monitoring shifts the display to this screen.,MonitoringSelect the monitorin,Failure History,Failure history of electrical system,Failure history of air-conditioner,Failure history of mechanical system,Select the item and press F6 switch,Pressing F2 switch era

37、ses the air-conditioner error.,E indicates that the system remains in error condition.,Deletion of failure history of the mechanical system is not available.,Select the failure history item and press F6 switch,Service Menu Screen,Failure History Select Screen,Failure HistoryFailure history,Failure H

38、istory Reset,Pressing +1,2,3 selects screen,Memorize necessary failure histories before erasing.,Press F2 switch ( CLEAR),Press F6 to erase all,Select the item and press F6 switch,Press F6 to erase selected item,Screen to erase all electrical abnormality record information,Screen to erase individual

39、 electrical abnormality record information,Failure History ResetPressing,Maintenance History,Select the maintenance item and press F6 switch,Maintenance HistorySelect the,Maintenance Mode Change,Select the maintenance mode change item and press F6 switch,Select the item and press F6 switch,Maintenan

40、ce Mode Change00 Maintenance mode using/not using01 Engine oil replacement intervals02 Engine oil filter replacement intervals03 Fuel main filter replacement41 Fuel pre-filter replacement04 Hydraulic oil filter replacement intervals05 Hydraulic oil tank breather replacement intervals07 Damper case o

41、il inspection and replenishment intervals98 Final case oil replacement intervals09 Machinery case oil replacement intervals10 Hydraulic oil replacement intervals99 Initialize all (not to be indicated on the menu),Maintenance Mode Change Screen,Service Menu Screen,00: Maintenance Mode On/Off screen,9

42、9: Screen to clear all to the initial set values,01: Engine Oil Change Interval screen 1,Maintenance Mode ChangeSelect,Telephone Number Setting,Select the telephone number setting item and press F6 switch,Make entry using the number keys (0 to 9) and press F6 key to confirm or press CLEAR to erase t

43、he entered number.,Telephone number will appear to the bottom if an error occurs,Pressing F5 SW returns to the preceding screen.,Service Menu Screen,Phone Number Entry screen,Telephone Number SettingSelect,Default Setting,Default Setting01Work mode on power-ON02Unit selection03Attachment yes/no04Att

44、achment/Maintenance password setting05Camera setting06ECO display setting07Breaker automatic judgment setting10Initialize all (not to be indicated on the menu),Select the default setting item and press F6 switch,Service Menu Screen,Default Screen,Default SettingDefault Setting,Work Mode Display on P

45、ower-ON,Select the work mode item on power-ON and press F6 switch,Work mode and travel display (2 sec),Normal screen,Start-up screen,If the breaker mode was selected, the screen to the left appears at start-up for each power-ON.,Select a mode item and press F6 to change the screen from the start-up

46、to a selected item.,Pressing F6 after entering 10 from the number keys on the default setting screen will set the default upon power-ON to the work mode the system was in when it was turned-OFF last time.,Work Mode Display on Power-ONS,Unit Selection,Select the unit selection item and press F6 switc

47、h,Pressing F6 after entering 10 (all to default) using the number keys in the default setting screen sets to the SI unit system mode.,Unit SelectionSelect the unit,Attachment-yes/no,Select the Attachment-yes/no item and press F6,Pressing F6 after entering 10 (all to default) using the number keys in

48、 the default setting screen sets to the Attachment-no mode.,Pressing F6 after selecting the Attachment-no deletes ATT from the work mode select screen.,Attachment-yes/noSelect the At,Attachment/Maintenance Password Setting,Select the item and press F6 switch,If selected to Use password, the password

49、 screen (diagram below) appears.,Pressing F6 after entering 10 (all to default) using the number keys in the default setting screen sets to the Attachment password not using mode.,Attachment/Maintenance Passwor,Camera Setting,Select the camera setting item and press F6 switch,Two (2) screens will ap

50、pear only when set for using Camera 1 and 2,Pressing F6 after entering 10 (all to default) using the number keys in the default setting screen sets to the three (3) cameras not in use mode,Set the rear mounted camera in reverse image,Camera SettingSelect the camer,ECO Display Setting,Select the ECO