图纸的专业术语的解释.ppt

1,图纸的专业朮语的解释,作成：束谦 2006-3-25,2,注解栏（NOTES）诠释图面指示处诠释,3,中达（DELTA)图面注解分析,一，铝包铁产品，以3310309900为例1.MATERIAL:SGLCCAZ170;ALUMINUM-ZINC COATED STEEL EN 10215-DZ51D+AZ185-C-C;t=1.0mm,OR EQUIVALENT-材料：DZ51D-C的铝包铁=镀铝锌铁-厚度T=1.0mm,4,中达（DELTA)图面注解分析,一，铝包铁产品，以3310309900为例 2.FINISH:ENAMEL PAINT,COLOR:PANTON COOL GRAY 5C.-表面处理：烤漆，顔色为冷灰5CWORD COLOR:PANTONE COOL GRAY 9C-丝印文字的顔色为冷灰9C,5,中达（DELTA)图面注解分析,一，铝包铁产品，以3310309900为例3.MUST MEET DELTAS SPEC.:10000-0002,10000-0094.10000-0162-产品必須符合中达标准：10000-0002,10000-0094.10000-0162,6,中达（DELTA)图面注解分析,一，铝包铁产品，以3310309900为例4.THE MARK:“*”ARE CRITICAL DIMENSIONS IN THE PARTS.PLEASE INSPECT IT BY EACH INCOMING LOT-“*”表示为该产品的重点尺寸,每批出货请按之做檢驗。,7,中达（DELTA)图面注解分析,一，铝包铁产品，以3310309900为例5.ABOVE PARTS ARE MADE BY NCT TOOLING,-以上产品用NCT(钣金）加工。6.Material Property(Ref.):Density=0.0078g mm3,mass=444.7575g.-材料密度为0.0078g mm3,重量为444.7575g-此项仅供參考,8,中达（DELTA)图面注解分析,一，铝包铁产品，以3310309900为例7.ALL SPOT WELDING POINTS MUST HAVEPAINTING ON BOTH SIDE,POINTING COLOR SHOULD SIMILAR AS MATERIAL-所有的点焊处，须有適當补漆处理，其顔色与材料顔色相近（指铝包铁材料的产品）。,9,中达（DELTA)图面注解分析,一，铝包铁产品，以3310309900为例8.ALL PAINT WORD STYLE MUST BE IN ACCORDANCE WITH“IMAGE FILE”。-所有的印刷字体须与图档一致。,10,中达（DELTA)图面注解分析,二，不锈钢产品，以3310337600为例1.MATERIAL:STAINESS SUS304 BRUSHED,t=1.0mm,STUD:STAINLESS.-材料：不锈钢SUS304,拉丝處理，-厚度T=1.0mm，铆钉：不锈钢,11,中达（DELTA)图面注解分析,二，不锈钢产品，以3310337600为例2.MUST MEET DELTAS SPEC.:10000-0002,10000-0094.10000-0162-产品必須符合中达标准：10000-0002,10000-0094.10000-0162,12,中达（DELTA)图面注解分析,二，不锈钢产品，以3310337600为例3.THE MARK:“*”ARE CRITICAL DIMENSIONS IN THE PARTS.PLEASE INSPECT IT BY EACH INCOMING LOT-“*”表示为该产品的重点尺寸,每批出货请按之做檢驗。,13,中达（DELTA)图面注解分析,二，不锈钢产品，以3310337600为例4.BURR HEIGHT CANT EXCEED 5%OF METAL.THICKNESS.-毛刺 批锋高度不可超过材料厚度的5%,14,中达（DELTA)图面注解分析,二，不锈钢产品，以3310337600为例5.PART MUST BE CLEAN AND FREE OF TOOL MARK&CHIP.-产品必須做清洗，不可有模痕和划伤等。,15,中达（DELTA)图面注解分析,二，不锈钢产品，以3310337600为例6.DIM.TOLERANCE MUST MEET TOLERANCE TABLE UNLESS OTHERWISE SPECIFIED.-除非有特別說明，公差必須符合公差表,16,中达（DELTA)图面注解分析,二，不锈钢产品，以3310337600为例7.Material Property(Ref.):Density=0.0078g mm3,mass=1435.9915g.-材料密度为0.0078g mm3,重量为1435.9915g-此项仅供參考,17,中达（DELTA)图面注解分析,二，不锈钢产品，以3310337600为例 8.ALL SPOT WELDING POINTS MUST HAVE PAINTING ON BOTH SIDE,POINTING COLOR SHOULD SIMILAR AS MATERIAL-所有的点焊表面，须有適當补漆处理，其顔色与材料顔色相近（指铝包铁材料的产品）。,18,中达（DELTA)图面注解分析,二，不锈钢产品，以3310337600为例9.PART MUST HAVE PE FILM ON THE SURFACE WITH BRUSHED FINISHED.-产品加工過程必須在拉丝處理后贴上保护膜。,19,中达（DELTA)图面注解分析,三，铜料产品，以3310053200为例 1.MATERIAL:C1020 OR C1100(Cu99.9%)T=2.0mm-材料C1020,或者C1100(含铜量99.9%），料厚T=1.20mm.2.FINISH:NI PLATING,5uM MIN.-表面处理：镀镍，镀层厚度5uM以上。3.MUST MEET DELTAS SPEC.:10000-0002-产品必須符合中达10000-0002标准。,20,中达（DELTA)图面注解分析,三，铜料产品，以3310053200为例4.THE MARK:“*”ARE CRITICAL DIMENSIONS IN THE PARTS.PLEASE INSPECT IT BY EACH INCOMING LOT-“*”表示为该产品的重点尺寸,每批出货请按之做檢驗。5.ABOVE PARTS ARE MADE BY NCT TOOLING,-以上产品用NCT(钣金）加工。,21,中达（DELTA)图面注解分析,四，SECC材料产品，以3312156002为例1.MATERIAL:SECC,T=1.6mm+-0.05t(THE ELECTRO-GALVANIZED STEEL SHEET,20g,2.8um PER SIDE AND MUST MEET GENETAL SPEC FOR ELECTRO GALVANIZED STEEL SHEETS THAT ISSUE ON OCTOBER,)-材料SECC，厚度为1.6+-0.05t，电解层20g，即单面厚度2.8um,並且要符合材料的行业标准。,22,中达（DELTA)图面注解分析,四，SECC材料产品，以3312156002为例2.FINISH:PAINTING COLOR:RAL7016-表面处理，烤漆，顔色为RAL7016.3.THE PART IS MADE BY NCT TOOLING,-该产品用NCT(钣金）加工。,23,中达（DELTA)图面注解分析,四，SECC材料产品，以3312156002为例4.EXTRUDE HOLE WITH THREAD MUST BE WITHSTAND 20KG-CM MIN.-抽芽孔的螺纹必須承受20公斤 厘米以上的扭力。5.STANDOFF MUST BE FLUSH ON SURFACE AND WITH STAND 20KG-CM TORQUE AND WITHSTAND 30KG PULL FORCE,STUDS&STANDOFFS MUST MEET THE STANDARD OF PEM OR EQUIVALENT.-STANDOFF 钉必須钉头平整，且要符合PEM标准，即能承受20KG-CM 的扭力和30KG的推力。,24,中达（DELTA)图面注解分析,四，SECC材料产品，以3312156002为例6.BURR HEIGHT CANT EXCEED 5%OF MATEL THICKNESS AND BURR SIDE TO BE INSIDE,OXIDIATION ON SHEARED EDGE IS PERMITTED BUT IT CANT EXCEED OVER SURFACE.-披锋高度不可超过材料厚度的5%，并且披锋面为内侧，剪口边允許有生锈現象，但不可溢出表面。,25,中达（DELTA)图面注解分析,四，SECC材料产品，以3312156002为例7.ALL RADII TO BE 2.0R UNLESS OTHERWISE SPECIFIED.-除非特別說明，所有R角为2.0。8.ANY TOOLING MODIFY IN PRODUCT MUST BE APPROVED BY DELTA ENGINEERING DEPARTMENT.-任何工艺更改必須得到中达工程部門的同意。,26,中达（DELTA)图面注解分析,四，SECC材料产品，以3312156002为例9.“*”IS CRITICAL DIM.WHICH MUST BE INSPECTED BY SUPPLIER IN EVERY SHIPMENT.-“*”为每批出货必須檢驗的重点尺寸。10.PART MUST BE CLEAN AND FREE OF TOOL MARK&CHIP.-产品必須做清洗，不可有模痕和划伤等。,27,中达（DELTA)图面注解分析,四，SECC材料产品，以3312156002为例11.THE PART MUST MEET DELTA ENERAL SPEC.:10000-0002;DIM TOLERANCE MUST MEET TOLERANCE TABLE UNLESS SPECIFIED.-产品必須符合中达一般标准10000-0002;除非有特殊說明，产品公差必須符合公差表。,28,中达（DELTA)图面注解分析,五，图面标注单词 短语解释SPOT POINT 焊点SPOT-WELDING 点焊ASSEMBLY MODE 組裝方式SINGLE MODE 单件方式ALL SURFACES 所有表面ALL OUTSIDE SURFACES 所有外表面ONLY OUTSIDE SURFACES 仅仅外表面INSIDE SURFACES 内表面,29,中达（DELTA)图面注解分析,五，图面标注单词 短语解释RIVET 铆钉INSERT PEM PF11-6-2 OR EQUALITY 嵌入PF11-6-2彈簧钉THREAD HOLE 抽芽孔SLOT HOLE 腰形孔CHAMER 倒角,30,中达（DELTA)图面注解分析,五，图面标注单词 短语解释PAINTING 烤漆POWDER COATING 喷粉PLATING 電鍍CHROMATE 铬酸盐SILK SCREEN 丝印MASKING THIS SIDE 此面防烤MARK ON THE SIDE 此面打字印ALL SCREW HOLE NO PAINTING 所有螺纹孔防烤,31,五，图面标注单词 短语解释PUNCH DIRECTION 冲裁方向BRUSHED DIRECTION 拉丝方向BURR SIDE 毛刺面NERA SIDE 近面FARSIDE 远面OPPOSITE SIDE 反面 对立面UPWARD 向上DOWNWARD 向下,中达（DELTA)图面注解分析,32,APC图面注解分析,FINISH:PER OS-ME-MATL.NO FLAKING OR PEELING OF FINISH PERMITTED处理：无，即为原材料本身。表面无压痕，划伤，详见标准OS-ME-MATL.REMOVE ALL BURRS AND SHARP EDGES.去除所有毛刺和利边。HARD TOOLED PARTS TO BE TREATED IN TOOLING.硬模产品的毛刺在加工過程已被处理。,33,APC图面注解分析,FINISH:POWDERCOAT ALL EXTERIOR SURFACES INCLUDING RIVET AND PEM HEADS USING“RAVEN BLACK”PER APC OS-ME-POWDER SPEC.處理：按APC喷涂标准对所有外部面进行喷涂處理；即“RAVEN BLACK”亦即EN333HG.包括拉钉头和PEM钉头。POWDERCOAT MUST COVER SHEARED EDGES.涂层必須覆蓋切断面。,34,APC图面注解分析,OVERSPARY PERMITTED ON INTERIOR SURFACES EXCEPT WHERE NOTED.除指示处以外，内表面允許有飛粉。MASK THREADS AND WHERE NOTED,螺纹和指示处需做防烤。REMOVE MASK PRIOR TO SHIPPING.出货前去除所有防烤物。ALL DIMENSIONS ARE PRE-PAINT DIMENSIONS UNLESS OTHERWISE SPECIFIED.除特別說明外，所有尺寸都是指喷涂后尺寸。,35,APC图面注解分析,SOFT TOOLED PARTS TO BE TIME SAVED IF NOT PRE-PLATED STOCK,COMMERCIAL BURR MUST PASS UL1778,371 SHARP EDGE TEST.如果不是预镀板，软模产品的毛刺必須及时去除。毛刺标准必須符合UL1778,371利边測試要求。,36,APC图面注解分析,ALL UNSPECIFIED RADII TO 0.50mm所有未注明的R角为0.50mmAVOID ALL SHARP CORNERS,AND CHAMFER AS SHOWN.为避免尖角，利边，均需有加工倒角.MAXIMUM BURR HEIGHT TO BE 0.10MM毛刺最大高度为0.10mm.BEND RELIEF CUTS TO BE 0.5*MATERIAL THICKNESS WIDE.折弯系数为材料厚度的0.5倍。,37,APC图面注解分析,Place mark in this area 此区域打字印REMOVE ALL SHARP EDGES ALONG THIS EDGES去除此边的所有利角To be welded on all four sides 四面全部烧焊To be welded only on two sides:this side and on the opposite side 仅两面烧焊，即此面和对面。Mask all this surface=No painting all this surface 此面防烤=不喷Mask all surfaces=No painting all surfaces.所有面防烤=不喷,38,APC图面注解分析,3D CAD DETABASE TO BE PROVIDED IN ADDITION TO PRINT.THE PRINT TO BE USED AS PART SPECIFICATION,SHOULD A DISCREPANCY ARISE BETWEEN PRINT AND DATABASE,CONSULT APC ENGINEERING.倘若3D图档附加打字印，因为字印是用来作为产品說明的，內容与3D图档有差异，请与APC 工程確認。,39,APC图面注解分析,MARK PART NUMBER,VENDOR ID,AND REVISIED.12IN OR 3 MM HIGH WHERE SHOWN,IF PART IS TOO SMALL TO MARK,BAG AND TAG WITH THE SAME INFORMATION.产品上需显示出产品编号，供應商代号和版号，高度为0.12英寸或3MM，若产品太小不能打MARK,包装箱和标识上需有同样的信息。,40,APC图面注解分析,ALL PARTS TO BE FREE OF ANY DIRT OR GRIME THAT PREVENTS LABEL ADHESION OR ALLOWS TRANSFER OF SUCH DIRT OR GRIME ONTO COSMETIC BEZILS AND COVERS。ALL VANISHING OILS USED MUST BE PRE-APPROVED BY APC MANUFACTURING AND APC QUALITY.ALL PARTS TO BE FREE OF SCRATCHES AND TOOL MARKS。FIRST PART APPROVALS WILL DICTATE PRODUCTION QUALITY.所有产品上的油污需去除（即影响标识脱落或运输过程中留下的影响外觀的油污）；所使用的挥发油需得到APC操作工和APC質量的認可；所有产品不可有划伤和模具痕，样品承認时将說明产品质量要求。,41,APC图面注解分析,BENDREDUCTION IS CALCULATED AT MEASURING THE UNFOLDED LAYOUT.SUPPPLIER IS RESPONSIBLE FOR CALCULATION OF BENDRE DUTION OTHER THAN STATED.折弯尺寸根據测量展幵設計来计算，供應商负责不同于規格的折弯尺寸的計算。,42,东伦图面注解分析,MATERIAL TO BE 2.00+-0.08 THK ALUMINIUM JIS A1100P 1 2 HARD材料：1 2 硬度的1100铝：厚度为 2.00+-0.08 mm去除此边的所有利角FINISH TO BE ALOCHROME 1200(YELLOW)表面处理为铬酸盐黄色。注：现已改为环保本色PART MUST BE FREE FROM SCRATCHES AND SHARP EDGES 产品不可有毛刺和划伤PART SHOULD BE FLAT AND SQUARE WHEN FORMED UNLESS OTHERWISE STATE除非特別說明，产品成形时应该是平整，垂直的。,43,东伦图面注解分析,ALL UNSPECIFIED RADII TO 0.50mm所有未注明的R角为0.50mmAVOID ALL SHARP CORNERS,AND CHAMFER AS SHOWN.为避免尖角，利边，均需有倒角加工.MAXIMUM BURR HEIGHT TO BE 0.10MM毛刺最大高度为0.10mm.BEND RELIEF CUTS TO BE 0.5*MATERIAL THICKNESS WIDE.折弯系数为材料厚度的0.5倍。,44,SO MUCH FOR TODAY今天至此为止！,THANK YOU VERY MUCH!谢谢大家！,