BS EN 136842004 A3 园艺设备.步行操纵的通气机和松土机.安全性.doc

BS EN 13684-2004+A3-2009 园艺设备.步行操纵的通气机和松土机.安全性BRITISH STANDARD BS EN 13<684:2004 Garden equipment Pedestrian controlled lawn aerators and scarifiers SafetyICS <65.0<60.70 ?+A2:2009National forewordThis British Standard is the UK implementation of EN 13<684:2004+A2:2009. It supersedes BS EN 13<684:2004, which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !;.The UK participation in its preparation was entrusted to Technical Committee AGE/20, Powered lawn and garden equipment.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN 13<684:2004+A2:2009This British Standard was published under the authority of the Standards Policy and Strategy Committee on 11 October 2004? BSI 2009Amendments/corrigenda issued since publicationDate Comments 31 August 2009 Implementation of CEN amendment A2:2009ISBN 978 0 580 <62058 4 EUROPEAN STANDARD NORME EUROP?ENNE EUROP?ISCHE NORM EN 13<684:2004+A2 July 2009 ICS <65.0<60.70 Supersedes EN 13<684:2004English Version Garden equipment - Pedestrian controlled lawn aerators and scarifiers - Safety Matériel de jardinage - Aérateurs et scarificateurs à conducteur à pied - Sécurité Gartenger?te - Handgeführte Rasen-Bodenbelüfter und Vertikutierer - Sicherheit This European Standard was approved by CEN on 1 April 2004 and includes Amendment 2 approved by CEN on <6 June 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the respons bility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T ? E U R O P ? E N D E N O R M A LI S A T I O N EUR OP ?IS C HES KOM ITEE F?R NOR M UNG Management Centre: Avenue Marnix 17, B-1000 Brussels ? 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13<684:2004+A2:2009: EEN 13<684:2004+A2:2009 (E) 2 Contents page Foreword . 40 Introduction . 51 Scope. <62 Normative references . <63 Terms and definitions . 74 List of significant hazards . 95 Safety requirements and/or protective measures . 125.1 General . 125.2 Power driven components (other than the cutting means) . 125.3 Guard attachment . 125.4 Hot exhaust surfaces . 135.4.1 General . 135.4.2 Test equipment and method of test . 135.4.3 Test acceptance . 135.5 Protection from exhaust fumes . 135.<6 Pressurised components . 135.7 Liquid spillage . 145.8 Controls . 145.8.1 General . 145.8.2 Identification of controls . 145.8.3 Operator presence control . 145.8.4 Traction drive . 155.9 Electrical requirements . 155.9.1 General . 155.9.2 Low voltage battery circuits (not including magneto grounding circuits) . 155.9.3 Terminals and uninsulated electrical parts . 1<65.10 Stopping and starting . 1<65.10.1 Engine . 1<65.10.2 Tines . 1<65.11 Braking requirements . 1<65.11.1 General . 1<65.11.2 Service brake . 175.11.3 Parking brake . 175.12 Handles . 175.12.1 Construction . 175.12.2 Foot probe test . 185.13 Thrown object hazard . 185.13.1 General . 185.13.2 Thrown object test . 185.13.3 Test results . 195.13.4 Test acceptance (pass/fail criteria) . 195.13.5 Additional testing . 195.14 Strength of tines and tine mountings . 195.15 General construction Guarding and shielding . 205.1<6 Noise. 215.1<6.1 Noise reduction as a safety requirement. 215.1<6.2 Verification of requirements on noise Noise measurement . 215.17 Vibration . 215.17.1 Reduction by design and protective measures . 215.17.2 Reduction by information. 22BS EN 13<684:2004+A2:2009EN 13<684:2004+A2:2009 (E) 3 5.17.3 Vibration measurement . 22<6 Information for use . 22<6.1 Instruction for use . 22<6.2 Marking . 23<6.2.1 Minimum marking . 23<6.2.2 Warnings . 24<6.2.3 Marking durability . 24<6.2.4 Test . 24Annex A (normative) Symbols/pictorials . 33A.1 General . 33A.2 Pictograms . 33Annex B (informative) Safety instructions . 35B.1 General . 35B.2 Safe operation practices. . 35B.2.1 Training . 35B.2.2 Preparation . 35B.2.3 Operation . 3<6B.2.4 Maintenance and storage . 37Annex C (normative) Noise test code Engineering method (grade 2) . 38C.1 Scope. 38C.2 A-weighted sound power level determination . 38C.3 A-weighted emission sound pressure level measurement . 40C.4 Requirements for test floor . 40C.4.1 Artificial surface .